Top 20
Element Electronics FLX-3211B 32 in. LCD HDTV Questions & Answers
After scanning channels tv still does not have picture or sound
What type of input and what type of cable have you set to ?
(a) Antenna - Coax cable (75 ohm)
(b) STB - HDMI
(c) DVD - HDMI or
(d) DVD - Red+White+Yellow
(e) DVD - Red+White+Optical (if your TV and DVD support it)
Most TV cannot find any channel when scanned without a proper external /internal antenna
8/11/2016 1:06:11 AM •
Element...
•
117 views • 0 helpful votes
Element tv stopped working model ELCFW329
Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
3/31/2016 5:06:22 AM •
Element...
•
303 views • 0 helpful votes
My element tv won't come on it has no indicator light
The worst offender is capacitor EC 13 (this is the location). It is located inside a heat sink shield (iron cage). The value is 25 volts at 330mf. Once the cage is removed replace these capacitors as well. EC14 & EC6, 35 volts at 100mf. EC10 &EC12, 35 volts at 470mf. EC8,EC7,EC9,at 16 volts at 1000mf. EC11,EC12 at 25 volts at 220mf. Please also resolder connection CON3. This connection will allow a good ground to the main board (also known as the signal board. Also you will have to replace diode HER304 (this is the location). This diode is mounted on a heat sink. Replace it with a NTE 576. f you cannot do this find an electronic hobbiest or a TV Shop. Take this info with you. Thanks for asking, Matt of Martins TV Repair.
3/31/2016 4:59:29 AM •
Element...
•
110 views • 0 helpful votes
Rest tv element 36 inc
There are two types of reset to TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience.
http://electro-medical.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.
1/7/2016 7:00:34 AM •
Element...
•
180 views • 0 helpful votes
Why does my celcus tv 40 inch smell so bad.
There should be something burning inside the circuit board. Never use the TV for long time in this condition. It might cause more faults to occur. Contact any service technician, and rectify the problem as far as possible. Never switch ON it, unitil then.
5/30/2013 10:01:10 PM •
Element...
•
78 views • 0 helpful votes
Connecting computer to Element flx-3211b via HDMI not working
I had the same issue with this TV in my hotel room. I set the FLX3211B TV up as an extension of my laptop, but had to change the refresh rate from the default 58p Hz to 60p Hz for the digital TV display. Once I did this, it came right up.
2/26/2013 5:06:24 AM •
Element...
•
467 views • 0 helpful votes
No Power
sounds like more of the same..what else do you have on same circuit sounds like electric company due to incur some costs unfiltered power
3/6/2013 2:07:12 AM •
Element...
•
53 views • 0 helpful votes
No power on my Element FLX 3202
The fact that the light isn't on is a sign that you lost Standby Power. Most likely you have a fault with the power supply board.
1/3/2013 9:00:53 PM •
Element...
•
197 views • 0 helpful votes
Not finding what you are looking for?