Element Electronics FLX3711B 37 in. LCD TV - Answered Questions & Fixed issues
I was watching my 37' LCD tv last night when I
Bad power board, it could be a regulator circuit in the board and you can troubleshoot it if your good at electronics as those switch mode power supplies can be a little tricky sometimes, it may make more sense to replace the board though, generally they aren't that expensive, under 50 bucks generally
12/1/2017 10:26:46 PM •
Element...
•
Answered
on Dec 01, 2017
•
127 views
How can I assure that the power supply unit PSU is defective?
You only need a PSU board if the back light inverters are combined with it. Otherwise look for the inverter board. To be sure it's defective, when the picture goes off shine a flashlight on the screen to see if you can spot movement from the program on the screen. If you can see movement then the inverter board needs replacing. If you can't see any movement then the T-Con board is bad. You can get parts from here:
TV Parts Universal TV Stands DLP Chips ShopJimmy
2/2/2016 8:09:15 PM •
Element...
•
Answered
on Feb 02, 2016
•
86 views
Picture disappear while sound still on?
My first go-to place would be any connectors you removed when you did the repairs -- as since this happened after a period of successfull run-time, HEAT may have caused them to expand to the point where a minimally-connected contact is failing. (And I admire your tenacity on taking on a job like that in the first place!)
1/30/2016 1:25:17 PM •
Element...
•
Answered
on Jan 30, 2016
•
605 views
Black shawdow at top left corner of screen
Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/
In some models of LCD TVS; the backlight inverter and its T'Con board will be a part of the panel itself, and will be a built-in type inside the LCD panel. If so, they can't be replaced. In this case; a panel replacement is the only repair. For some other models, the backlight inverter section circuit will be a part of the main power supply regulator [SMPS]. To such sets, the power supply section circuit too should troubles shoot. Contact any service technician. The circuit will differ with models and versions.
Type in the brand name of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts. It will make surf easy.
4/9/2015 6:06:58 PM •
Element...
•
Answered
on Apr 09, 2015
•
56 views
I need the screen for the element flx3220
Tv LCD Screen panel are cost the same as a new tv,bacause the picture screen panel are 90% importmant to the tv.Tries websites like Shopjimmy.com,Ebay.com might have refurbish tv LCD screen panel for sale.
1/25/2015 7:45:17 PM •
Element...
•
Answered
on Jan 25, 2015
•
152 views
My tv goes loud and low
is it the TV or the source? Does it do this on all inputs? try attaching DVD player.
Be sure all your connecting cables are good & installed all the way on both ends. if still have issue, may be your Main PCB
part#
ELEMENT FLX-3711B MAIN BOARD 899-KE0-UF3712XA1H & Signal Board 899-100-GF271XAH
try this web site for element parts: http://www.ebay.ca/sch/sis.html?_nkw=Polaroid%20899%20KE0%20KF371XA%203H%20Main%20Board%20VSC%2037V1&_itemId=161027387391
5/8/2014 7:12:42 PM •
Element...
•
Answered
on May 08, 2014
•
70 views
Replaced 3 capcitors today and
check D7 and small cap to the right(forgot # returned tv) in the power supply area.i found diode leaky and cap dry.Thats how i fixed the blinking red light.hope it works.
7/28/2011 11:51:31 PM •
Element...
•
Answered
on Jul 28, 2011
•
241 views
TV volume got louder and then shut off, when this
Cover the IR (infrared receiver) window on the TV with masking tape or electrical tape and see if it works as expected. If it does, a stray signal may be commanding your TV to behave this way. The commend source could simply be a stuck button on a remote. The next thing would be to remove all the remotes from the room and remove the tape from the TV. Bring the remotes back in one at a time to determine which is causing the problem.
Once isolated, repair or replace the remote.
6/2/2011 12:00:18 AM •
Element...
•
Answered
on Jun 02, 2011
•
100 views
I was just given an
you will need the power specs of each unit, look on the tv and computer near where they plug in, should be tagged right there or somewhere close. by law it has to be tagged. if not right there keep looking . and yes it is specific.
3/13/2011 12:12:40 AM •
Element...
•
Answered
on Mar 13, 2011
•
130 views
While watching the T.V. I started experiencing a
Your set has a problem with its power supply. If it is under warranty, have it replaced ASAP. If your warranty has expired, you can take the set to any good repair shop - ask for an estimate before having any work done to it.
2/19/2011 7:02:39 AM •
Element...
•
Answered
on Feb 19, 2011
•
266 views
Bought element tv model flx-3711b
Hello,
The problem you are having is a common and easily repaired one. The problem is caused by a failing power supply board. If you can do a little soldering then you should be able to do the repair. Check out this article on repairing the power supply in this model.
http://www.ccl-la.com/blog/index.php/visco-vsc-37v1-no-picture-lets-repair-it/If you don't want to do the repair yourself we do offer a repair service, you can use the link on that page to request service.
I hope this helps you, if so please rate our solution.
BuddyMc
11/23/2011 9:23:54 AM •
Element...
•
Answered
on Nov 23, 2011
•
997 views
Not finding what you are looking for?