20 Most Recent Element Electronics FLX2211B 22 in. LCD TV - Page 3 Questions & Answers

Unfortunately, what you're describing is a repair issue. You won't be able to address the problem with troubleshooting. There is a part inside the TV that needs to be replaced. If you're under warranty, this will cost you nothing. If you're not under warranty the cost will likely be a minimum of $200 parts and labor. However, be warned that the cost could be considerably higher. You should call the manufacturer for your full range of options.


I hope I've provided you useful assistance and that this information allows you to make an informed decision as to how to proceed from here. Please be sure to vote on my response. I hope I've earned a good rating from you today.

Please post a comment if you need additional assistance so that I can help you further

has problem on the board.the solder is loose or loose solder

there is a small square board that the screens ribbon cable connects to. htat board is usually called the digital board.
The digital board will need replaced, unfortunatly in most cases the only way you can get a digital board is to order the screen with it.
The price of the screen will cost as much as a new one.
Try E-bay and find one with something like sound problems and swap the parts. otherwise buy a new set. sorry!

I finally got my hands on a manual. I haven't checked as yet, but there is a 4A 250V - 5X20mm Time Lag fuse (slow blow) under a plate next to AC plug on the rear panel. I pulled the back panel to do a visual and didn't see anything burnt or fried. I'll get back to you if I discover the fuse was blown.

I have run into the same problem with a different model (32 inch from Circuit City). You may have found that there is almost no support from the co or web. I do not have an official solution but have some work arounds that have done the job for me.
WA#1 = after a channel scan tune to a HD/digital channel before you turn the set off. You need to do this each time for several times, because the set when turned on to a regular cable or analog station will default to skip all channels. After several times the set should remember your channels.
WA#2 = after a channel scan, go to the skip channel section of the menu, and if your remote has the colored buttons on the bottom scroll through the channels using the red and green (up and down on this menu) buttons. This apparently helps the set remember not to skip your scanned channels.
These are not glamorous solutions but appear to trick the TV into not re-setting the skip function for the channels.
Best of luck.

try auto adjustment feature if it does not work try resetting it to factory default
b coz typical operation ,manual is not provided by manufacturers

Ok, I am having the same issue. I just bought my tv - same model at the Target Black Friday sale. Can I ask, did yours make a low humming noise before you changed it out. I still am within my 30 day exchange policy, so I am thinking it would be wiser just to exchange it... but my concern is, would I get one with the same problem (or worse) in exchange?

Where your Smart TV already has an app in its app pages, start that app, log onto your Netflix account (which you need to pay for) and watch away. If your TV does not have a Netflix app, give Player a try at http://www.Playora.com - this is an app that runs on a PC and lets you open content on the screen of the PC and toss it to a lot of different Smart TVs (Samsung, Panasonic, LG, Sony, JVC, etc.). Ithing, It will be helpful for you.

I lost the screws for my legs for my 50 inch element TV????

http://www.fixya.com/support/t26576974-element_tv_no_picture_good_sound_but

Some sets and devices have HDMI control that can turn off and on devices connected to them. Look into the settings of both devices and search for anything to do with HDMI control.

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electro-medical.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.