20 Most Recent Sharp 32SC260 32 inch TV - Page 5 Questions & Answers

go into set up change language to English if no luck factory reset

Sharp Televison... | Answered on May 19, 2019

Could be a blown capacitor. If you're electronically inclined. Unplug the TV and remove the back plastic cover. Look on the circuit board for and bulging capacitors. Or little black spots near leads. If you find something like that. you will need to disolder the component and install a new one. I fixed a Panasonic that had a similar issue.

Sharp Televison... | Answered on May 18, 2019

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
For some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.
Search the site by type in the "brand name" of your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
{View the site in web view or by a desktop to see the search box. Mobile view has no search box.}

Sharp Televison... | Answered on May 17, 2019

Use the side controls tu git menu. If darkness doesnt work u probly hav worn screen. Buynew tv theyr cheap

Sharp Televison... | Answered on May 16, 2019

Hello... It sounds like you have a backlight failure, and the image going away during the flashlight test is due to the TV going into "Protection" mode. A service technician may be able to go into the service menu and clear the lamp error codes and get the TV working, or it may need the backlights replaced. I hope this helps...

Sharp Televison... | Answered on May 16, 2019

Make sure the internal speakers are turned ON
That is an adjustment in the AUDIO menu.

Sharp Televison... | Answered on May 13, 2019

1) Press Channel down and Volume Down button from LED panel a same time.
2) Page option will display.
3) Select 9/10 page by pressing up and down button.
4) EEP option will display.
5) Press Ok button.
Switch Off and Switch On from Main LED work properly

Sharp Televison... | Answered on May 12, 2019

This 'K' usually denotes that you are in the 'service mode', and to exit it, you normally just switch off at the mains, (unplug the TV).

If you press 'input' and volume down ('-') together, OR,
volume down '-' and channel down '-' together,
that should take you into you into the service menu proper.
You use channel up/down to navigate the menu, (and volume up/down to alter the values).
You could try this, and see if there's a 'Factory Reset' option if just switching off doesn't work, but DON'T alter any of the service settings (if you use the reset, you will have to re-tune etc.)

Sharp Televison... | Answered on May 12, 2019

Request the diagram directly from Sharp. Be sure to specify the type of diagram you wish, e.g., schematic

Sharp Televison... | Answered on May 10, 2019

Clearly something has happened that is forcing the resistor to handle too much current and while it is tempting to believe the culprit is close by, the difficult fact of dc coupled circuits means the possible fault could be several stages away. Troubleshooting modern electronics is really a job for an experienced person who has access to a service sheet and appropriate test equipment, especially an oscilloscope. Modern digital electronics and switch mode power supplies mean a voltmeter is less use than a means of examining waveforms and duty cycle...

Sharp Televison... | Answered on May 08, 2019

if it has a usb slot then id say yes..

Sharp Televison... | Answered on May 08, 2019

check connections and input or source

Sharp Televison... | Answered on May 04, 2019

if cords don't match try a converter to combine cords and change input or source

Sharp Televison... | Answered on May 04, 2019

Not finding what you are looking for?
Sharp 32SC260 32 inch TV Logo

Popular Tags

9 questions posted

Ask a Question

Usually answered in minutes!

Top Sharp Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76100 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Cindy Wells

Level 3 Expert

5968 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sharp Televison & Video

  • Sharp Televison & Video

Most Popular Question

grandson turned

  • Televison & Video