20 Most Recent Panasonic KX TG2237S Cordless Phone (KX-TG2237S) - Page 5 Questions & Answers

You may have exceeded the REN value of the number of phone on your phone line. Try this Unplug all phones, from main and the cradle, remove all handset batteries. The one that is hard wired to the phone jack. plug in the mains, plug in the base to telephone jack. Put the batteries in the hand set and verify it works. Now go to each extension one by one, plug those in and adding the handset batteries and verfiying each one works. You may get to a stage where the last one doesn't work.

try here.hope it helps http://panasonic.ae/en/manuals/KX-TG4311.pdf

You can't. It doesn't have that feature. http://pdfstream.manualsonline.com/3/3958afec-4877-ba94-99a1-6bbc5981b223.pdf ..

Page 40 says it has an alarm and goes off at a certain time! https://a.sellpoint.net/a/dGgnR6Yz.pdf ..

Try this How do I reset my Panasonic cordless phone to factory settings? How to Factory Reset Panasonic Phones

1. Press the Menu soft key (middle soft key) at the bottom of the screen.
2. Select System Settings from the menu.
3. Enter #136 on the keypad.
4. Select Yes when asked if you are sure you want to factory reset the phone. The phone will be reset successfully after startup.

some videos that _may_ be useful. https://www.google.com/search?q=Panasonic+TGA520M+used+handset%2C+how+can+I+deregister+it+without+the+base+set ..

Edited post to TFG370 from tgf 370. this is the manual for the TGF370 series. It just says that it stores the last 10 numbers called, rather than an address book. https://help.panasonic.ca/viewing/ALL/KX-TGF372C/OI/TG175CSK_PNQX6719YA/TG175CSK_PNQX6719YA.pdf?a_id=54175&session=-1DWse*o ..

Check the connections.

The PNLC1017 is the charger for the handset of some Panasonic cordless phones. One of the compatible handsets is the KX-TGA660 which works with the KX-TG4112 system. However, the 'Check tel line' message indicates a problem at the base or the POTS (Plain Old Telephone Service) telephone line. The system is not hearing the dial tone. Check that the power adapter is plugged in to a live outlet and is warm. If it's cold, than the power transformer is not working and the base has no power. If there is power, check if the handset message disappears when the handset is close to the base. This is usually rare but indicates a transmitter/receiver in the handset or base is not communicating properly. You can try to de-register all handsets and then register them again. To check the phone line, I prefer to use an older corded phone. These don't require power to work. First, try a new phone data cord (RJ-11) between the base and the wall jack. (I've seen someone accidentally use a handset cord which doesn't work.) Test if there is a dial tone when this cord is plugged into the test phone. If there is a dial tone, then if the cordless phone base didn't work with the replacement cord, the base is faulty. Replace it or contact Panasonic if the system is under warranty. If you have a DSL fliter, this may be damaged. If it's inside, replace it. If it is in the service box, ask your telephone provider to check it. If there is no dial tone, you need to locate the other phone jacks for that phone line. Find where your phone service comes in as well. Check if there is a dial tone on another jack for that phone line. If there is no dial tone, check the service box for an RJ-11 jack, Test for a dial tone there if you can plug in the RJ-11 cable. If you have a dial tone at another jack, then the problem is local to the first jack's wiring. You can open the jack and check for loose wires. There are two styles of jacks - screws or punch-down. For the screw terminal, strip the insulation and wrap it under the appropriate screw. For the punch-down keystone jack, you need a punch-down tool. The tool is available from most home improvement/building supply stores, in the wiring section. Do not strip the wire. Use the tool to press the wire down into the correct slot on the jack. See https://www.lanshack.com/wire_phone_jack.aspx for the wiring diagram. If you can't test the phone line or there is no dial tone at the service box, then you need to contact your telephone provider. It used to be that the provider would always test and fix outside problems for free. Some telephone companies are trying to stop repairing copper wiring. If you have a dial tone at the service box, then the problem is somewhere in the inside wiring. You may want to get someone to find a broken wire in the wall for you. Your telephone company service technicians will do this for a fee. I hope this helps. I've had the check tel line issue times several times at my home. Twice, the outside line was damaged by mice and repaired by my telephone company. Once, a lightning strike damaged the DSL filter; it was promptly replaced. Other times, the line was damaged by contractors digging too close to the underground utilities. The contractors got the wiring repaired. When our service was switched to a fiber-optic system, we lost one telephone jack when the installer simply didn't plug in the wire. We found the loose wire behind the siding and plugged it into the port in the service box ourselves. Since then, we lost telephone and other service intermittently when the modem card in the service box was failing. That was also replaced by the telephone company technician. Cindy Wells

Edited question for clarity. Moved to the correct Category. Worst manual ever, but it is just the handset to the base unit. Nothing mentions blocking

Installation Manual - Panasonic Support

https://help.panasonic.ca > TGEA40_PNQX7787ZA

PDF Nov. 12, 2015 - Installation Manual. Additional Digital Cordless Handset. Model No. KX-TGEA40. Thank you for purchasing a Panasonic product. 16 pages However, using the correct search query, it is mentioned here, top of the page. I can't paste, because symbols don't work. https://www.google.com/search?q=model+kx-tgea40+remove+blocked+caller ..

You are too far away from the base station to the phone you are using, or the aerial on the base station isn't extended up, (if it has one). Experiment! Make a call standing next to the base station.

then contact the provider we can not do it for you

Has the answering system been turned off? Check the base, there is an Answer On button with a LED indicator. If the light is off, press the Answer On button. From the handset when the phone is in Standby, press Menu/OK and navigate to Answering Device using the Up/Down arrows. Press Menu/OK to enter the Answering Device menu. Use the arrows to go to the Answer On and press Menu/OK. Then press Off to exit the menu system. If you are calling into the phone, you can turn on the answering system. Let the phone ring 15 times followed by a long beep, then enter your remote code within 10 seconds. Either hang up or do any remote operations. Note: pressing 0 will turn off the answering system. When you set up the ring count, the maximum rings before the system picks up is 7. In Toll Saver, the phone rings twice if there are new messages and 5 times otherwise before you hear the greeting. Even when the recording space is full, your greeting or a pre-recorded "mailbox full" statement will play. (Note: some of these systems allow for a greeting to play without saving any messages. This is controlled by the "recording time" option.) I hope this helps. See the manual for the KX-TG4021 on the support page: https://shop.panasonic.com/support-only/KX-TG4021N.html. The current link to the manual is https://ftp.panasonic.com/telephone/om/kx-tg4011_mul_om.pdf . Start on page 27 for the Answering Device information. Cindy Wells

Caller ID is a service provided by your carrier - at a price.

Do you remember the password used to enable the Dial Lock? If someone else enabled the lock, you may need to consult the prior user. The steps to disable the lock: with the phone system in standby mode (no calls in or out), press Menu on the handset. Use the Up/Down arrows to reach the line labeled "Dial Lock". Press Select (the right soft key below the LCD screen). Enter the four digit password and press Save (the right soft key, again). (If the handset beeps 3 times and displays "Save error". the wrong password was entered.) If you get past the password section, press the right soft key again to disable the Dial Lock. See pages 54-55 of the manual, http://panasonic.ae/en/manuals/KX-TG2361.pdf , for information on the Dial Lock feature. I hope this helps. Cindy Wells (If a password of more than 4 digits was entered, only the last four digits are stored by the telephone.)

There doesn't appear to be a way. Sometimes on multi-phone business systems, a technician can connect a laptop with dealer software and make changes or edits that a user can't. If that particular number needs to be at Number 1, you would have to delete them all and reprogram them all again. http://www.voicesonic.com/panasonic/manuals/KX-T76xx_User_Guides/KX-T7630_User_Guide.pdf ..

Could be line trouble. Have your carrier check.

you pay your phone service provider to have caller id

The KX-TGA401C handset works with the KX-TG401x, KX-TG403X and KX-TG651x phone systems among others. If you have the appropriate base, see the suggestions below. Does your handset read Ringer Off? Try setting the ringer volume. With the phone system in standby (no calls in or out for any handset), press Menu. Navigate using the Up/Down arrows to Initial Settings. Press Menu/OK. Navigate to Ringer Settings and press OK. Press OK again to enter the Ringer Volume sub-menu. Use the Up/Down arrows to set the ringer volume and press OK to save. Press Off to exit the menu system. The other possibility is that the handset is not registered to the base. Note: only 6 handsets can be registered to the base. If you previously registered 6 handsets, you need to deregister some of them. To register the handset, hold the handset near the base since you will need to press buttons on both. Press Menu on the handset and navigate to and enter Initial Settings. Navigate to Registration and press OK. Navigate to HS Registration and press OK. On the base, press and hold the Locator button for 5 seconds and the registration tone sounds. Press OK on the handset you are trying to register. If all the registered handsets start ringing, you triggered the Locate handset function. Press the Locator button again. Then do the press and hold step again. Only press OK on the handset when you hear the registration tone. You can find the manual for the KX-TG4011 here: https://shop.panasonic.com/support-only/KX-TG4011N.html . The direct link to the manual is https://ftp.panasonic.com/telephone/om/kx-tg4011_mul_om.pdf . See page 21 for the directions to set the ringer volume. I hope this helps. Cindy Wells (You can't register a handset to an incompatible base. The communication protocols don't work.)

Not sure what you mean 'configure the system to play on external device', (music on hold?) but here is your manual for both units. https://www.teledynamics.com/tdresources/bd33f39d-c9ba-4150-b610-a50b9a86e114.pdf ..

bin it and get a new one