20 Most Recent Panasonic KX-T7730 Corded Phone - Page 4 Questions & Answers

KX-T7730 Phone must be connected with a 4wire line cord. you may be tested it with a 2 wire line connector.because other normal phones only needed 2wire line cords.Just connect a new 4w cord to under socket located to main unit & other end connect directly to the tel;system & see is the phone confirmed OK.
& let me know .Good luck.
[email protected]

Basically, there are 2 ways of programming the date
and time - the short way and the long way.
If you are using the KX-T7730 phone on a Panasonic
KX-Txx 308/824 system:

SHORT WAY:
From the Switcboard / Main telephone
( ext 101, 10 or 9 ) with the handset on the
cradle/hook:
1. Press PROGRAM 0
2. Enter Date and Time
( The format is: yymmdd,
1 to 7 1=Monday 2=Tuesday etc, hh:mm,
0 or 1 0=AM 1=PM ) see example
3. Press AUTO DIAL / STORE to save your changes
4. Press PROGRAM to exit program mode

EXAMPLE:
If the date and time is 3 February 2010 Tuesday 2:15 pm you will enter as follows:
100203 2 02:15 1

LONG WAY:
From the Switcboard / Main telephone ( ext 101, 10 or 9 ) with the handset on the cradle/hook:
1. Press PROGRAM * # followed by the system
password ( default is 1234).
2. Now press 000 and then SP-PHONE.
Enter the year.
3. Scroll to the month with the right scroll key
(located at the right bottom corner of the phone).
To change the month use the AUTO ANS / MUTE
button.
4. Now scroll right again and change the date and
day.
To change the day, again use AUTO ANS / MUTE
5. Scroll right again and the time will appear.
Set the time.
To change am/pm scroll to it, and again,
use the AUTO ANS / MUTE button.
6. Press PROGRAM to exit program mode and you
are done.

From the idle phone press PROGRAM line 1's button and dial 0 1 STORE. That puts line 1 back under the button.

Press PROGRAM or pick up the handset and set it back down to exit programming.

Carl

There are three types of CALL FORWARDING:1. All Calls: Means all of your calls will be diverted to another extension Go On Hook+ Press 711 +Ext. No. + # then go Off Hook2. Busy/No Answer: Means when your extension is Busy the call diverted to another extension. Go On Hook +Press 712 + Ext. No. + # then go Off Hook3. To Oustide CO Line: All calls will be diverted to Outside Line (eg. Mobile Phone/Home Phone) Go On Hook + 713 + 9 + Number + # + Go Off Hook

Yes.

Yes. However, it will only work if you have the 8-port hybrid card(TDA0170) installed. Besides costing a lot more money(the card, not the phone) the phone uses 4x the power of a 76xx or DT series phone and you only get 12 lousy working buttons.

Carl

Hello Joyce Sia, You have two ways to cut off ringing... Look for a "DND" (do-not-disturb) control... used for napping, studying or just plain being left ALONE... ELSE... On the LEFT side of your base you should also have a slide switch... a CRUDE volume has three settings: - big bell = High Volume - small bell = Low Volume - bell with an "X" over the top = OFF Check these settings BEFORE you do a general power and battery remove.. and begin All over AGAIN... Ask com What Your Question

What phone system is the 7730 connected to and do you have CID hardware?

have you replace the spiral cord of the handset? if you do may the handset is defective, try replacing the handset, if you have extra unit try to borrow and connect it to your phone just to see if its good or not.