20 Most Recent Panasonic KX-T7731 Corded Phone - Page 9 Questions & Answers

Did you program the 2 buttons for CID-S and CID-I?

I can tell you how to do it, but it won't mean too much if you don't have the other programming done.

Try storing 96 and 97 under a couple of buttons.

Carl

Not possible. A Panasonic Analog PITS phone has only one ring sound and all CO rings match.
The TD series and 74xx phones were the first phones to have 8 ring tones. The TDA series has 30 different tones. Prices are fairly competitive for upgrading.

This is done through installer level programming typically by a service technician.

Calls log auotmatically to phones that ring. If more than one phone rings the call will log on the phone that answers. If no phone answers, the phone connected to the lowest port number will log the call. The lowest port number is usually the lowest extension number, but not always depending on how the phone system installer numbered and connected the extensions. Also if a call is transferred to a phone it will log. The logged calls can be seen by navigating the LCD screen.

Typically DND is turned on and off by pressing the FWD/DND button. There are three status conditions for this button indicated by the button light.
button light off: both features off(Forwarding and Do Not Disturb)
button light blinking red: Forwarding on
button light solid red: Do Not Disturb on

The functionality of this button can be customized by the phone system installer to work differently than outlined above. Station features can also be accessed through station programming using the LCD screen by pressing the button then either scrolling through the features using the LCD screen navigation keys or entering the specific program number as in 50 for FWD/DND programming.

How do I reset from the attendant station or access 999

There are two passwords you could be asking about, the electronic station lock, or a voice mail password. Each has a different login procedure and is based on the hardware you have, not the phone type.

Since this is an open forum, it is not possible to give specific details about equipment you didn't mention, but if you look around your documentation, you'll find the instructions for administering both the phone system and voice mail. One is reset from the attendant station, and one from mailbox 999.

Carl

Since the phone can work on about 18 different systems, that depends.

790 on the intercom clears extension data. It may not set it back to "original settings".

Carl

On the intercom dial *7510 (*7511 turns it back on in a TDA-50 or lower) and *751x (1 or 2) turns it on in a 100 or larger.

Carl

enter system programming
Press PROG *#1234
use arrow keys up and down to find date and time - use NEXT key it the screen to move on to next screen

Programming can only be done from a larger style handset on any extension number

depending on what system you have here are 2 options for personal messages -
TVM system dial into voicemail (usually 200 or 500) dial 3 1 1 and follow the prompt (the older system is option 5 1 1)

SVM dial *382 your message will be played back to change it dial *381


Button programming
Press PROG
Press BUTTON to store
Press 1
enter extension no of who you want
Press STORE

This is one of those conditional answers. Your 7731 works on one of 18 different Panasonic systems. Which one is yours? In a TA series, you get 5,10,15, or 20 seconds before the forward works. That's all you have. It's different in a TAW, TD, TDA, and probably non existant in any system prior to the TD.

The time is adjusted system wide as program 202. In a TAW and TDA it's adjusted per phone.

Carl

Your extension reads 102 because that is the extension #.
Press either the tranfer key or the " * " star key and your display will change to time and date or just the date.

Press PROG/PROGRAM
Press the button you want to store the number under
Press 2
Enter the number to dial (remember to prfix with your line access code usually a 9)
Press STORE

HUH? You program autodial for the SYSTEM from a SYSTEM phone in SYSTEM programming. You program the "auto dial" buttons, the ones on the right side of your phone from the phone by pressing PROGRAM one of the 12 buttons and dialing "9" plus the number SAVE.

If you are trying to program one of the left side buttons for autodial (bad move) then you dial "29" first.

Carl

What manual? The message on hold comes from an external source plugged into the system cabinet. It has it's own manual had hardware.

Carl

What happens when you dial 700-0 on the intercom?

7731's work on 18 different Panasonic models, but they were first delivered with the later TA series phone systems. You could press the MESSAGE key and look at the display to see where the message came from, but I don't think you can erase it on a 7731. So, just record the fact, then 700-0 and poof. All gone.

Carl

It really depends on which one of group of up to 18 cabinets your 7731 is connected with, but in a TA series, 714# on the intercom sets, 710# clears. You can also press Intercom the FWD/DND button and dial 0#. (or 4# to set it again)

Carl

take its all cord out for few seconds and then plug em again..