20 Most Recent Pride Mobility Products Used Jazzy 1120/2000 Electric Wheelchair - Page 9 Questions & Answers


The chair could be in freewheel and will not work until you move the levers to drive position. Or you could still have the charger still plugged in Hope this helps

Pride Mobility... | Answered on Aug 17, 2010


You will need two U1 batteries

Pride Mobility... | Answered on Aug 17, 2010


I think it would be easier for you to contact pride mobility or your provider and have then send you a new cable. If Medicare purchased your chair then they will pay for the repair Hope this helps

Pride Mobility... | Answered on Aug 17, 2010


Hi,please rate me as in thumbs up 1 to 4,im disabled myself & i do cause i care & not for money.I suggest ring age concern,im sure they will point you in the direction of a scooter repair agent in your area.Hopefully you should be mobile soon,take care Colin.

Pride Mobility... | Answered on Aug 04, 2010


Your scooter requires two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance free. They are recharged by an off-board charging system. ! Charge your scooter’s batteries prior to using it for the first time. ! Keep the batteries fully charged to keep your scooter running smoothly. READING YOUR BATTERY VOLTAGE The battery condition meter on the tiller console indicates the approximate strength of your batteries using a colour code. From right to left, green indicates fully charged batteries, yellow a draining charge and red indicates that an immediate recharge is necessary. To ensure the highest accuracy, the battery condition meter should be checked while operating your scooter at full speed on a dry, level surface. The off-board charger supplied with your scooter is equipped with a 115/230 voltage switch. Confirm that this switch is in the proper position for your locality. If you are not sure what the voltage is in your country, contact your local electricity dealer before inserting the charger power lead plug into your wall socket. If the setting is incorrect, the charger will not function properly. Slide the voltage switch to the appropriate position. The fuse controls the internal wiring harness.When its remove the wires controlling the scooter stops functioning.And due to that battery stops drawing. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.


Pride Mobility... | Answered on Jul 07, 2010


After about 6 months sitting without being charged the batteries rarely recharge properly. Bad news is you likely need new batteries.

Pride Mobility... | Answered on Jun 27, 2010


www.pridemobility.com/.../mobility.../INFINFB2040_Sonic_Troubleshooting.pdf
www.pridemobility.com/...Manuals/product_owners_manuals.asp
www.pridemobility.com/
I have searched extensively, for a service manual, schematics etc, however i was unable to find any. I suggest you contact Pride, and ask them for a service and repair manual. I have included links, to Pride, also their troubleshooting procedures, and the other one is for your user manual, which will be handy. Sorry I couldn't help more.

Pride Mobility... | Answered on Jun 04, 2010


You have moisture in the electronics. Purchase a can of electronic cleaner and spray all the electronic connections to remove any moisture. Make sure you purchase electronic cleaner which will remove the moisture and dry in seconds.

Pride Mobility... | Answered on Mar 09, 2010


hi, check the connections that goto the rear of the chair,

This is normally a troublesome area, make sure the connections are clean and fit well.

Regards
GeWiz.

Pride Mobility... | Answered on Jan 09, 2010


Sounds like your joystick is damaged. This chair probably has a PG Drives Technology joystick that serves as both the joystick control and acts as the power control module. If it has been damaged by say, running into a wall or doorway or table, this can be the cause, or if it has gotten moisture inside it, that will hurt it as well. Other possibilities are overloading the chair past its weight capacity or driving it over unstable terrain like sand, gravel, much etc.

Pride Mobility... | Answered on Aug 28, 2009


Assuming you didn't get the PC board mounted inside the top of the tiller assembly wet, or the power controller located under the shroud, then you likely either have one or two of the batteries that are bad, or a bad charger. You will need a voltage tester that you can pick up cheap for about $6.00. Set to the DV voltage setting in the 50-100 volt scale. Remove the seat and the shroud and test the voltage at each battery. If good, they should read about 12.25 volts or more, not higher than 14. If one is normal and the other lower, say 10 Volts, that low one is bad, but you should probably replace both with fresh gel batteries, fully charge before using. If both batteries are about 12 VDC, then plug in the charger to the chair as usual, and take another voltage test on each battery. The voltage should read higher now that the charger is on. If they aren't, then your charger has no output. Some chargers you can test output voltage on without them plugged in by testing across the two horizontal pins on the 3-pin connector that you plug into the chair. The output voltage should be about 26 volts. If it is 24 or less, you need a new charger. Good luck.

Pride Mobility... | Answered on Jul 24, 2009


sounds like a loose terminali had a similar problem on my scooter and i fixed my problem by tightening those up

Pride Mobility... | Answered on Jun 24, 2009


you are asking the internet for medical advice? ask your doctor. he knows your history

Health & Beauty | Answered 5 hours ago


hi Carol, the control module being the controller ? on that scooter it is one of two types, a eGis ,, square black or chomie looking unit or a blue, grey unit , a Curtis..

Can you tell me what the fault is ?

I can repair them as they are a specialist items.

Regards
Rob

Health & Beauty | Answered 8 hours ago


hi, okay sounds like a faulty wig wag( throttle pot ) that is connected to the lever that makes your scooter go forward or backwards, try gently pushing in the upwards direction as you push the lever , or pulling down as you pushed the lever forward, what you 're doing is seeing if the tracks within the wigwag pot or worn by moving the lever in the up and down position you are making a good connection again.

Regards
Rob

Health & Beauty | Answered 8 hours ago


call doctor from home

Health & Beauty | Answered Yesterday


hi, have you tried speaking to pride about this ? the question is , is it faulty ? or need lubication , a picture would be really helpful .


regards

Health & Beauty | Answered Yesterday


Stop the cut and pasting, it shows how you are lacking real business acumen to do real good

Health & Beauty | Answered Yesterday


Stop the cut and pasting, it shows how you are lacking real business acumen

Health & Beauty | Answered Yesterday

Not finding what you are looking for?
Pride Mobility Products Used Jazzy 1120/2000 Electric Wheelchair Logo

56 questions posted

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1402 Answers

Will

Level 1 Expert

25 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Pride Mobility Products Health & Beauty

  • Pride Mobility Products Health & Beauty

Most Popular Question

wheelchair just stops will only turn in

  • Health & Beauty
Loading...