20 Most Recent Salter 3007 Aquatronic Digital Scale - Page 2 Questions & Answers

How to open up the Salter 3007 Aquatronic Digital Scale:
1. Look for a hole (covered by a label) on the bottom of the device, not far from the L-R centre line, and about 1-3/4" from the front. Peel back the label and use a small cross-head screwdriver to loosen the screw that can be seen though the hole (needs about one turn, no need to remove it). Place the scale upright, and rotate the weighing pad slightly in a clockwise direction. This will disengage the tabs on the plastic pad which hold it to a metal base, so that it can be lifted off. 2. Remove the six screws recessed around the bottom of the scale. 3. Place the scale upright and gently "snap" apart the top and bottom shells (catches molded into the left and right ends). Be *** VERY CAREFUL *** when doing this as the display is held in place on a plastic bridge by the upper shell. When this is removed the display is loose except for a flexible plastic printed connector strip (which links it to the circuit board). It is *** all too easy for this strip to break away at one end or the other ***.

mcdevito75 here, Chances are the digital portion is burnt out, You can try an appliace repair shop in your area, I don"t think you"ll be able to get the wire schematic, you can also try to call the manfacturer or vist online. Sorry!

I contacted Salter and unfortunately the scales cant be repaired. Could you please remove my request. Thank you.

Probably the sensor is damaged and time to replace the scales unless it is still under the manufacturers warranty, in which case, return it for service.

See if you can find the manual for your model. It sounds like you have a British model and not one that has US units. http://www.manualsdir.com/brands/salter/41.html

Here's some videos and other sites... https://www.google.com/search?q=salter+bathroom+scale+not+working&newwindow=1&sxsrf=APwXEde5CBJdho-KS23VtouG2r7hLRdYvQ%3A1686263335252&source=hp&ei=J1aCZLamDZOO0PEPlaatkAU&iflsig=AOEireoAAAAAZIJkNx5F0HgbTkFWtmOACeIM1J5xxhWA&oq=Salter+bathroom+scale+not+showing+weight&gs_lcp=Cgdnd3Mtd2l6EAEYADIFCAAQogQyBQgAEKIEOgUIIRCgAVAAWPkjYLhTaABwAHgAgAHEBIgB-weSAQcwLjMuNS0xmAEAoAECoAEB&sclient=gws-wiz

Hold the two arrow and set buttons together for a few seconds and it may clear.

I have never known a food scale take a 9 volt battery. Mine takes x CR2032 3 volt button battery. Google make model manual

https://www.youtube.com/watch?v=tb0hwlLsFGs

2 batteries

O-ld is 'overload'. There are some fixes here. The first thing I would do is remove the battery and leave it overnight. Replace the batteries with new ones. If you think it may be possible that you are overloading the scale, put a bag of sugar or flour on them to test.https://www.google.com/search?q=Salter+bathroom+scales+0-ld+code..

Chris try leaving the battery out for ten minutes and then place it in scales

The replacement battery could be defective or incorrectly installed. Aside from that, the the scales may have simply failed.

Either you are trying to weigh something that is too heavy or the damage has already been done and the sensor has been damaged with excess weight. I bought a set just recently from ASDA (Wallmart) and they cost less than £10.

The EE code means there is an error, possibly because the replacement batteries are defective or installed incorrectly.

I think it will help https://slavinasmile.ru/