20 Most Recent
Mountain Plumbing AG600S Air Gap for Reverse Osmosis Systems - Page 3 Questions & Answers
Everpure faucet leaks at handle, how to fix ??
If your Everpure faucet is leaking at the handle, the problem could be a faulty O-ring or a worn-out cartridge. Here are the steps you can follow to fix the leak:
- Turn off the water supply: Before you start working on the faucet, make sure to turn off the water supply to prevent any accidents.
- Remove the handle: Use a screwdriver to remove the screw that holds the handle in place. Once the screw has been removed, you can gently pull the handle off the faucet.
- Check the O-ring: Look for an O-ring around the base of the handle. If the O-ring is damaged, worn or missing, it can cause water to leak from the handle.
- Replace the O-ring: If the O-ring is damaged, replace it with a new one. You can purchase O-rings at a hardware store or online.
- Check the cartridge: If the O-ring is in good condition, the problem could be a worn-out cartridge. You may need to remove the cartridge and replace it with a new one.
- Reassemble the faucet: Once the O-ring or cartridge has been replaced, reassemble the faucet by putting the handle back in place and tightening the screw.
- Turn on the water supply: Finally, turn the water supply back on and test the faucet to see if the leak has been fixed.
If you're having difficulty fixing the leak or if the problem persists, it may be best to contact Everpure customer support for further assistance. They can help you diagnose the problem and recommend the best solution.
2/12/2023 10:35:06 AM •
Plumbing
•
Answered
on Feb 12, 2023
Why does touchless water faucet only work when other faucet turned on?
It's possible that the solenoid valve in the touchless faucet is not functioning properly, and needs to be replaced. Another possibility is that there is a loose or broken wire in the electrical circuit that powers the solenoid valve. You may want to check the connections and wiring, and consult a plumber or electrician if necessary, to help diagnose and repair the issue.
1/29/2023 12:55:57 PM •
Plumbing
•
Answered
on Jan 29, 2023
Water flow is low on WR Kitchen Faucet.
i'm guessing ...but... take it off ..take it to the outside faucet or water hose hold the hose end tight on the faucet outlet and turn it on to back flush it what went in should come out .. but have you checked the screen on the spicket (where the water comes out) that usually unscrews an you will see a screen inside there that can get clogged in addition to several plastic aerator bits that can get clogged and this is a LOT easier than removing the faucet and back flushing it ..
1/14/2023 12:10:57 PM •
Plumbing
•
Answered
on Jan 14, 2023
Goulds j5s keeps shutting on and off repeatedly the n cuts off before over heating.
- Check the suction line for blockages or kinks: Make sure that the suction line is clear and that there are no blockages or kinks in the line that could prevent the pump from priming.
- Check the impeller: Make sure that the impeller is not clogged or damaged, as this can prevent the pump from priming.
- Check the voltage: Make sure that the voltage to the pump is within the specified range.
- Check the pressure switch: Ensure that the pressure switch is functioning correctly and that the pressure switch cut-out is set to the correct pressure.
- Check the thermal overload: Ensure that the thermal overload is functioning correctly and that the pump is not overheating.
- Consult the manual: Consult the manual for specific troubleshooting and service information for your Goulds J5S model.
1/14/2023 1:33:25 AM •
Plumbing
•
Answered
on Jan 14, 2023
Low hot water pressure at mixet tub/shower valve
You have a blockage on the hot water inlet to your shower valve . If all other hot oulets are fine . Take the valve out and check the mixer body for blockage . Or do you have a valve on the hot side that is not fully on .
1/8/2023 7:48:26 PM •
Plumbing
•
Answered
on Jan 08, 2023
The clip on my push pull faucet is frozen and will not move up or down any idea how I can get it to move. Thanks
- Try applying a penetrating oil such as WD-40 to the clip and moving it back and forth to help loosen any rust or debris that may be causing it to stick.
- Use a pair of pliers or a small wrench to gently grip the clip and try to move it up and down. Be careful not to apply too much force, as you don't want to damage the faucet.
- If the clip is still stuck, you may need to remove the faucet handle and access the clip from the inside. Depending on the design of your faucet, this may require removing a setscrew or using a special tool to access the clip.
1/3/2023 11:22:38 PM •
Plumbing
•
Answered
on Jan 03, 2023
Sediment from bladder entered pipes, clogging some
Remove all the faucet aerators and flush the system for at least 2-3 minutes. Try not to turn the faucet valves off too hard until you flush the system so you don't embed grit into any faucet washers or washerless valves.
Clean the debris from all aerators. Flush all toilets at least 10 times and check for any debris in the toilet tanks. Clean out as needed.
If you have outdoor spigots, flush those as well.
You could consider adding an inlet strainer to your water supply piping, especially if you are on a well, private or public.
12/23/2022 11:56:13 AM •
Plumbing
•
Answered
on Dec 23, 2022
Can someone help a plumbing novice out please with my waterfall mixer taps grub grate key
99% of the time it's a small Allen. Sizes differ. It will be one the small to mid sized ones though. I put them on all the time. If its corroded just be patient and try all of them. Don't force anything, and make sure it's a snug fit in the screw. If you round it off by using a key that's too small you're going to have to cut it off. You got this
11/20/2022 1:24:21 AM •
Plumbing
•
Answered
on Nov 20, 2022
Reverse Osmosis air gap faucet leaking.
this is an easy fix and quite common. I found that removing the drain line where saddle is mounted and clean it from the inside.
A common leaking problem in most taps is the "air gap leak." It occurs when water leaks through the hole on an air gap faucet.
An air gap is a vital component of the reverse osmosis system. It prevents the back flow of water into the reverse osmosis unit. Instead, the air gap directs the excess water into the drain lines.
When a lot of debris accumulates in the drain line, it clogs up, creating back pressure that forces water to flow out through the air gap. Unfortunately, the back flow can flood your countertop.
To fix this problem, remove all the debris accumulated in your drain line to allow water to flow smoothly. You can use a wire brush or a pipe cleaner to clean out the drain line, starting from the end connected to the system's drain saddle.
You should also clean the system's drain saddle and ensure that it's properly aligned with the drain line. That's because the drain saddles can sometimes shift away from the drain lines.
To avoid air gap leaks completely, treat the drain line regularly using a natural cleaner that can dissolve the solids blocking it. Also, avoid flushing big chunks of food down the drain line.
8/28/2022 4:39:59 PM •
Plumbing
•
Answered
on Aug 28, 2022
My GE 153 will fill and drain but will not spin or agitat
The main motor is not running. I suspect water damage to the controller, probably corrosion on the motor wiring terminals. Also check the motor itself for signs of corrosion, especially at the terminals and the centrifugal switch housing at the end opposite the pulley..
8/7/2022 5:44:43 AM •
Plumbing
•
Answered
on Aug 07, 2022
Not finding what you are looking for?