20 Most Recent
Yukon Fitness Caribou Iii Gym Package Cpkg Cco - Page 6 Questions & Answers
Hobart profi fx90a dishwasher missing link to STE?
Hi,
your machine might need maintenance. You can reach out to a Hobart service agent to get this maintenance done. I didn't see any error code associated with "missing link", you might check your device manual for this before calling the agent. Thank you.
Hi, I have a Freeclimber 4600 CL, it will work fine on all resistance levels but after about 15min it will suddenly lose all resistance and just drop, I'm thinking it's the alternator but unsure
It's possible that the alternator is the issue, but there could be other causes as well. It's also possible that the problem is with the console or the wiring. Here are some steps you can take to troubleshoot the problem:
- Check the console: Sometimes, the console can cause issues with resistance. Make sure that the console is functioning properly and that there are no error messages or other issues.
- Check the wiring: Make sure that all the wiring is properly connected and that there are no loose connections or damaged wires.
- Check the alternator: If you suspect that the alternator is the issue, you can test it using a multimeter. If the alternator is faulty, it will need to be replaced.
- Check the power supply: If the machine is not getting enough power, it can cause issues with resistance. Make sure that the power supply is working properly and that the machine is receiving the correct amount of power.
If you're unsure about how to perform any of these steps, it may be best to contact a professional technician for assistance.
My treadmill run for a few second and stops
There could be several reasons why your treadmill is stopping after running for only a few seconds. Here are a few things you can check:
- Power source: Make sure your treadmill is properly plugged in and that the power outlet is working.
- Safety key: Ensure that the safety key is in place and fully inserted into the console. If the safety key is not properly inserted, the treadmill will not function.
- Motor: If the motor is not working properly, the treadmill may stop after running for only a few seconds. Check the motor by turning the treadmill on and listening for any unusual noises.
- Belt: A loose or worn-out belt can cause the treadmill to stop running. Check the belt tension and replace the belt if necessary.
- Control board: If the control board is malfunctioning, it can cause the treadmill to stop running. Check the control board for any signs of damage or wear.
If you are unable to diagnose the issue, it may be best to contact a professional to come and take a look at your treadmill.
My Trojan Runx treadmill on start up is slow to get to speed and when i climb on while at speed you can hear it losing speed.
There could be a few possible reasons for your Trojan Runx treadmill to have this issue:
- Belt tension: The treadmill belt may not be tight enough, causing it to slip and lose speed. You can adjust the belt tension by using an Allen wrench to tighten the bolts at the back of the treadmill.
- Motor: The motor may be overheating and shutting off, causing the treadmill to slow down. You can check the motor by opening up the motor cover and looking for any signs of burning or overheating.
- Motor brushes: The motor brushes may be worn out and need replacing. This can cause the motor to run slower and eventually shut off.
- Power supply: The power supply to the treadmill may be insufficient, causing it to lose speed. Make sure the treadmill is plugged into a dedicated circuit and not sharing power with other appliances.
If you're unsure about how to diagnose or fix any of these issues, it's recommended to contact a qualified technician or the manufacturer for assistance.
Lifecore R100 rowing machine display not working
If the display on your Lifecore R100 rowing machine is fully on but not responding to any selections, it may be a sign of a software or hardware issue. Here are a few troubleshooting steps you can try:
- Check the power source: Make sure the rowing machine is properly plugged into a working outlet. If it is, unplug it and plug it back in to see if that resets the display.
- Reset the machine: Try resetting the rowing machine to its factory settings. Look for a reset button on the console or in the user manual. Press and hold the button for a few seconds until the display turns off, then release the button and turn the machine back on.
- Check the connections: Make sure all cables and connections are secure and not damaged. If you find any damaged cables or connections, replace them.
- Contact customer support: If none of the above steps work, contact the manufacturer's customer support for further assistance. They may be able to walk you through additional troubleshooting steps or send a technician to repair the machine.
1750 commercial Norditrack treadmill stuck on Whoops error occurred.
The "Whoops" error on a NordicTrack treadmill usually indicates a software or connectivity issue. Here are a few steps you can try to troubleshoot the problem:
- Unplug the treadmill from the power source and wait for a few minutes before plugging it back in.
- Make sure the treadmill is connected to a stable and reliable Wi-Fi network. If the issue started when you tried to connect to the Internet, this could be the problem.
- If the issue persists, try resetting the treadmill's software by following these steps: a. Hold down the Stop button and the Speed Up button while inserting the safety key. b. Hold the buttons until the treadmill beeps twice. c. Release the buttons and wait for the treadmill to reset.
- If none of these steps work, contact NordicTrack customer support for further assistance.
It's also possible that the previous owner may have sold you a defective treadmill, so you may want to consider reaching out to them for a refund or replacement.
Not finding what you are looking for?