20 Most Recent Qca Spas Jewel Series Topaz Plus Hot Tub - Page 5 Questions & Answers

https://www.manualslib.com/manual/1592331/Coleman-90403e.html?page=5#manual

if your hot tub is tripping the breaker, it could be due to a worn out ground fault circuit interrupter (GFCI) breaker, which is responsible for preventing electrical surges. You can try flipping the breaker to see if it trips again. If it does, then you may need to replace the breaker. Another possible cause of the problem could be loose electrical connections in your hot tub . This can lead to power fluctuations that cause your hot tub circuit breaker to trip. Professional electricians can inspect your hot tub and tighten any connections that are loose, which should fix the circuit breaker problem. If your spa is not receiving power, you should check your home's circuit breaker to ensure that it's not tripped . Reset the circuit breaker if it's tripped to restore power to the spa. If the circuit breaker keeps tripping, it may be an indication of an electrical problem, and you should call a professional electrician to diagnose and fix the issue

According to the South Seas Spas Owner's Manual, the filter cycle begins 6 minutes after the spa is energized and the second filter cycle begins 12 hours later. The filter duration is programmable and can be set to 2, 4, 6, or 8 hours for continuous filtration (indicated by "FC"). The default filter time is 2 hours. It's possible that your filter cycle duration is set to continuous filtration mode. To change the mode, press the "Warm" or "Cool" button and select a duration of 2 hours. If this doesn't resolve the issue, it's recommended to contact a professional technician for further assistance.

possible water flow problem in spa mode

On the control unit select the 'up' arrow to cycle through the LED lighting options. Some units will only have one option (Blue) while other models will have a spectrum of colours to select from. Control unit diagram illustrated here https://www.hottubhiremerseyside.co.uk/faqs/

It sounds like the power surge coming back on damaged the controller. Try disconnecting the mains supply overnight to fully dissipate all voltage in the electronics. It that doesn't work, this is the maker, reach out for support.

Wide Selection of Topside Panels

Balboa Water Group - https://www.balboawatergroup.com > Spa Products Electronic Controls · Slimline® Jet Collection · Bath Jets · Zen Look Collection ... Balboa the largest manufacturer of hot tub panels in the world. These panels ... ..

Remove weights, Thoroughly clean cleaner, backwash filter system to get optimum suction. Check filter system for optimal suction..., ie. leaks, excess debris, clogged baskets, strainers, etc..

2 'hot wires'? Don't mess with 220 volts and water that you are going to immerse yourself in. Call and electrician or the pool company and do it properly to current electrical code by a qualified professional.

Paul, Found this info... https://www.justanswer.com/pool-and-spa/fpr35-rheem-pool-heater-hp6-error-code-no-clue.html Best to you

Try here; https://www.manualslib.com/products/Caldera-Tahitian-6976269.html

no info generic answer when pump is on [to make temp ] the jets are also on

Tony, Ck these sites on how to identify it... https://duckduckgo.com/?t=ffab&q=hot+tub+idendifier Best to you.

If the controller for your Prowler 920 robotic pool cleaner is not turning on or powering up properly, here are a few steps you can take to troubleshoot the issue: 1. Check the Power Supply: Ensure that the power supply is properly connected to the controller and that it is receiving power. Verify that the power cord is securely plugged into a functioning power outlet. You can try plugging another device into the same outlet to confirm that it is working correctly. 2. Inspect the Controller Display: Take a close look at the display on the controller. If any error codes or messages are displayed, consult the user manual or contact the manufacturer for further instructions on how to resolve the specific issue indicated. 3. Reset the Controller: Try performing a reset on the controller. Look for a reset button or a combination of buttons to press and hold simultaneously for a few seconds. This action can often help resolve minor software glitches and restore the controller's functionality. 4. Check for Loose Connections: Ensure that all cables and connections between the controller and the power supply or the Prowler unit are securely plugged in. Sometimes, a loose or faulty connection can prevent the controller from turning on. 5. Replace Batteries: If your controller uses batteries, make sure they are not depleted. Try replacing the batteries with fresh ones and see if the controller powers up properly. 6. Contact Manufacturer Support: If the above steps do not resolve the issue, it's recommended to reach out to the manufacturer's customer support. They can provide you with further assistance, troubleshooting steps, or advise on any potential repairs or replacements that may be needed. Remember to consult the user manual that came with your Prowler 920 for any specific troubleshooting steps or contact information for customer support.

circulation pump failure

Hot Tub Error Codes - Spa Topside Error Messages

Hot Tub Essentials https://www.hottubessentials.ca > hot-tub-error-codes 1) Hot Tub Error Codes (Alphabetical) ; COOL, Spa water is more than 20° F cooler than the temperature set point ; CP-ER, Circ pump failure ; DR, dr, dy?

google Mastercraft jet pump Model #561471 parts If it as described I would put new pump in. If you chose rebuild it A new is is $250 on eBay.

If the control panel indicator lights on your pool system do not consistently light up when the pool is turned on, it could indicate a potential issue with the control panel or the electrical connections. Here are some troubleshooting steps you can take: 1. Check Power Supply: Ensure that the power supply to the control panel is stable and consistent. Make sure the power source is providing the correct voltage and that there are no loose or faulty connections. 2. Inspect Wiring Connections: Verify that all wiring connections to the control panel are secure and properly connected. Loose or damaged wiring can cause intermittent issues with the indicator lights. 3. Clean and Inspect Control Panel: Check the control panel for any signs of dirt, debris, or corrosion. Clean the control panel and its components using a soft cloth and a mild cleaning solution. Inspect for any visible damage or loose components. 4. Test Indicator Lights: While the pool is running, observe the control panel and try to identify any patterns or triggers that may cause the indicator lights to come on. Gently tap on the control panel to see if it affects the lights. This could indicate a loose connection or a faulty component within the control panel. 5. Consult a Professional: If the issue persists or you are unable to identify the cause of the inconsistent indicator lights, it is recommended to contact a professional pool technician or the manufacturer's customer support for further assistance. They will have the expertise to diagnose and resolve the specific issue with your pool control system. Remember, working with electrical components requires caution. If you are not experienced or comfortable working with electrical systems, it is best to seek professional help to avoid any potential safety hazards.

You didn't give us a Make and Model but here are some sites that answer that question for varied Makes.. https://www.google.com/search?q=digital+pool+heater+is+displaying+sw+open+error&source=hp&ei=ZoKPZO-nHLfF0PEP0-iW6A8&iflsig=AOEireoAAAAAZI-QdpNy-irsShPIybO1gAWJJK1zy3Tx&oq=digital+pool+heater+is+displaying+sw+open&gs_lcp=Cgdnd3Mtd2l6EAEYADIFCCEQoAEyBQghEKABUABYAGDsM2gAcAB4AIABjAKIAYwCkgEDMi0xmAEAoAECoAEB&sclient=gws-wiz

See page 18 of the saltwater instruction guide ... 93 means it is on stand-by, power saving mode. Nothing is wrong, it's just waiting for the timer to tell it to turn back on automatically. If you want the system to be on right now, just turn the power switch off, wait a couple seconds and turn it back on.

Maybe a call to their coustomer support 888 #. Ck here..... https://images.inyopools.com/cloud/documents/dolphin-troubleshooting-guide.pdf