Top 20 Bosch 24 in. SGS66E02 Exxcel Built-in Dishwasher Questions & Answers

get the dishwasher filtration system at www.dishwasherfilter.com. this product was made to solve this problem. awesome product and guaranteed results.

It is possible that the machine does not start off the cycle because there are errors or feedback from the inputs. For the program to start up the main program controller must initiate the INLET/PUMP MOTOR/DRAIN to work when it is commanded .If this does not happen then the voltage at these points must be checked or the fault relates to no voltage/drive from the controller. This means the controller is a suspect.

check these error codes.

http://fixitnow.com/wp/2010/09/01/bosch-dishwasher-test-programs-diagnostic-mode-and-error-codes/

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor. The water pressure must be good and the spraying must be seen to be good. If there is low pumping or pressure then the spray arms will not turn around to inject with pressure. If so the pump must be checked for clogging.

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the drain valve/pump activated so as to drain off all the water.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.espares.co.uk/advice/dishwashers/a/3

For spares click On:

http://www.espares.co.uk/search/dishwashers/p/1083

Thank you for using Fixya.

Will work just as well, in fact if you are using a wash that is lower than 50 degrees it will work better.
All the best.

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes

This is the parts schematic that shows all the parts and where they are located. The noise is either something stuck in the pump or a dry bearing. https://www.searspartsdirect.com/model/25b4iqte9a-001794/bosch-she58c02uc-50-dishwasher-parts ..

Dishwashers come in standard sizes. Your old one is 60 CM wide and made for built in. https://www.bosch-home.ca/en/supportdetail/product/SGU4025AU/31 DISHWASHER 60 CM BUILT-IN/BUILT-UNDERSGU4025AU/31 As long as the new one is also for built in, the dishwasher will fit. Measure the height of the space you have. There may be a little height adjustment on the feet. ..

That is just saying the Child Lock (CL) has been activated.

Deactivate the child lock ' Bosch

Bosch Home https://www.bosch-home.com > ... > Get support 1. Press and hold the start button for three to five seconds ... When the child lock is activated, there will be a message "CL" in the display and all the washing ...

Bosch dishwasher child lock problem

Bosch-home.co.uk https://www.bosch-home.co.uk > ... > Dishwashers Hold down the lock button for three to five seconds. You should hear an audible beep and/or see the symbol disappear. The child lock is now deactivated.

What does CL mean on a dishwasher? And how do I fix it?

Quora https://www.quora.com > What-does-CL-mean-on-a-dish... This code means that the CHILD LOCK or CONTROL LOCK feature has been activated. When activated, all buttons will not change except the washer's door and the ... 9 answers · Top answer: First, look on your dishwasher to find a label that shows the manufacturer and the model number. ...

How to turn off the CL on the display of a bosch dishwashe...

JustAnswer https://www.justanswer.com > Appliance Repair Oct 28, 2010 - You should just be able to just turn the power button off, then turn it back on and the CL should be gone. 1 answer · Top answer: Hello, and thank you for using this service. I'll be helping you with your ..https://www.youtube.com/watch?v=Xr4DBwACUW4

AI Bot Answer Deleted. In the base of the dishwasher above the floor there is a plastic tray that has a leak sensor. If you see water behind the machine than it means you have a 'spraying leak' as the sensor cuts off the machine as soon as it is triggered. It is likely to be a leaking hose on the pump. It can also be caused by the machine over-filling. An E15 error code indicates that the safety switch has detected water in the base of the dishwasher. Your leakage protection system has activated. What can I do to fix the E15 Error Code on my dishwasher? Please turn off the water inflow and contact Bosch Customer Support for assistance.

E15 Bosch Dishwasher Error Code

Check if there is anything in the large item trap or blocking the water level sensor. The dishwasher won't try to fill if it believes it is full. Try pressing and holding the Start button for 3+ seconds. The Clean LED should light up in a minute. If it does, try the on/off button and starting a new cycle. (This just clears any old programs from the memory.) Some washers will stop if they detected a water leak. Sometimes turning off the power for a while and checking for water in the cabinet below the dishwasher or in the motor area is useful. The more likely items to check: Check the wiring between the inlet valve and the control board. Check the wires for corrosion at the connecting pins and for continuity. Broken conductors don't send a signal to open and close the valve. If those are okay, then the control board itself may be faulty. Since this dishwasher is discontinued by the manufacturer, I don't know if all of the parts are still available. The only parts list for the SHE3ARL2UC/28 that I found is here: https://www.partselect.com/Models/SHE3ARL2UC/ . They don't list any wires or the control board. I hope this helps. Cindy Wells

Add some salt.

It needs descaling. Try CLR in a wash

I have a Bosch Silence Plus 46 dBA. SHS5AVF6UC/22. ...

JustAnswer https://www.justanswer.com > Appliance Repair Jul 5, 2021 - What have you tried so far? When I try to start the cycle, the red light on the floor comes on, it beeps, but won't start. 1 answer · Top answer: Hi and welcome to Justanswer. My name is ***** ***** to assist you today. I'm Why is my Bosch dishwasher beeping and not starting? Bosch dishwashers are designed to beep when there is an error. A beep means that your drain is not clogged, and the rest of the parts are functioning as they should. Beeping in the middle of the cycle points to the problem with the control board itself. Find the circuit breaker and turn it off for 60 seconds.

Bosch Dishwasher Error Codes ~ By I-Fix Appliance Repair

The water supply is inadequate for your dishwasher.

The senors for your dishwasher are either dirty or need to be replaced.

https://www.reliableparts.ca/catalog/Touch-Up-Paints-467065 and Amazon of course!

Black Appliance Touch Up Paint

Amazon.com https://www.amazon.com > black-appliance-touch-up-... Rust-Oleum Paint 213174 .6-Ounce Specialty Brush Bottle Appliance Touch Up, Black, 0.6 Ounce. Enamel, Acrylic, Specialty. ..

If you're seeing an E3 error on your Bosch built-in microwave, it usually indicates an issue with the touchpad or control board. Here are some steps you can take to try to fix the problem: 1. Unplug the microwave: The first step is to unplug the microwave from the electrical outlet for at least a minute. This will reset the control board and may clear the error code. 2. Check the touchpad: Sometimes, the E3 error can be caused by a stuck or malfunctioning touchpad. Check the touchpad for any damage or debris that may be interfering with its operation. Clean the touchpad with a soft, damp cloth and make sure it is completely dry before plugging the microwave back in. 3. Replace the touchpad: If the touchpad is damaged or not working properly, it may need to be replaced. Contact a Bosch authorized service center to order a replacement touchpad and have it installed by a qualified technician. 4. Replace the control board: If the touchpad is not the issue, the E3 error may be caused by a faulty control board. Again, contact a Bosch authorized service center to order a replacement control board and have it installed by a qualified technician. In any case, if these solutions do not work, it's best to contact a qualified technician to diagnose and repair the issue, as microwave repairs can be dangerous due to the high voltage involved.

You never mentioned anything about dirty dishes not getting clean. Run a load and let it go and tell us the results.

If you can see water flowing down the overflow channel to the pan at the bottom of your Bosch dishwasher while it is running, this indicates that there may be a problem with the dishwasher's float switch or water inlet valve. The float switch is a small device located at the bottom of the dishwasher's tub that is designed to detect the water level inside the dishwasher. If the water level rises too high, the float switch will shut off the water inlet valve to prevent the dishwasher from overflowing. If the float switch is not functioning properly, it may allow water to continue to flow into the dishwasher, resulting in water flowing down the overflow channel to the pan at the bottom. Another possible cause of this issue could be a faulty water inlet valve. The water inlet valve is responsible for regulating the flow of water into the dishwasher. If the valve is stuck open or is not functioning properly, it may allow water to continue to flow into the dishwasher, resulting in water flowing down the overflow channel to the pan at the bottom. To resolve this issue, you may need to have a professional technician inspect and repair your Bosch dishwasher. They can test the float switch and water inlet valve to determine the cause of the problem and replace any faulty components as needed.

If the dishwasher is not starting the wash cycle after replacing the circulating pump, it is possible that there is an issue with the control board. You may want to check the wiring connections between the control board and the new pump to make sure they are properly connected. If the connections are correct, you may need to test the control board and its various circuits to see if there is an issue with any of the components. It is also possible that there is a problem with a sensor or switch that is preventing the dishwasher from starting the wash cycle. You may need to consult the dishwasher's user manual or contact Bosch customer support for further assistance.

You can find a replacement clic assembly for your Bosch 1587vs jigsaw online from Bosch or from third-party retailers. You can also find clic assemblies from hardware stores, home improvement stores, or tool supply stores in your local area. Make sure you get the correct clic assembly for your Bosch jigsaw model.