20 Most Recent Bosch 24 in. SHX46A05UC Built-In Dishwasher - Page 8 Questions & Answers

Try cutting electrical power to it for 5 minutes. That may set electronics

Could be a defective cycle timer

It doesn't turn off at the end of the cycle because the cycle timer is stuck.

Domestic dishwashers work by taking cold water and soaking the dishes as the water warms. Then it gives a good wash at high pressure, drains, refills, rinses and then hot rinses to dry. If it is slow because of slow filling, check the water pressure and also clean the strainer filters on the supply hoses where they go into the machine. If you want speed, buy a small under-counter commercial machine. They fill with hot water, have a tank heater and a rinse tank heater and the whole cycle is 3 1/2 minutes. Glasses first, plates and cutlery next, and pots and pans last. Seems to be a known issue!! Videos here with solutions https://www.google.com/search?q=Bosch+Dishwasher+SHE43C+cycle+takes+too+long ..

https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Dishwasher/31-129--/Bosch-Dishwasher-Won-T-Start

my dishwasher e01cod show then turn off

Check dishwasher water flow pressure switch in right side

h:01 means 1 hour delay. Press the delay button repeatedly to get to h:00 then hit start.

In the instructions for different models of Bosch dishwashers, the e27 error is described as insufficient voltage in the electrical network. This means that if the mains voltage drops below 220V (or 110V in some countries), the dishwasher stops working, and the E27 error code appears.

No! If you go to https://www.appliancepartspros.com/ you can put in the model number for the pump and it will list all the compatible replacements.

Most of these units have a waterproof solenoid inlet on the hose. If yours has this you can pull out the rubber washer in the end revealing a plastic mesh cover. This can also be pulled out with pliers. It can be a bit stiff to take care not to muller it! Under the plastic mesh is also a restriction valve which helps to slow the water pressure down. This has a little plastic shaft with a small rubber seal around it and can also be pulled out and cleaned.

Water protection system activated.Turn off water supply. Call customer service and quote the fault code.https://finderrorcode.com/bosch-dishwasher-error-codes.html

May wish to call customer service number shown in online manual: https://www.searspartsdirect.com/manual/nh6v021o60-001794/bosch-she43rl5uc-64-dishwasher (I don't list numbers here because of fraudulent1 spammers who post on FIXYA to deceive.)

Hello. The control panel most likely wasn't the problem...the main control board probably was blown out causing the user interface to remain off. What was the unit doing or not doing that made you replace the control panel? BIG TIP--if you had a power interruption (such as lights dimming in the house--called a "brownout") or a full scale outage where the clocks reset, the main board very well could have been damaged by the current surge when the power came back on. *NORMALLY**, if the appliance wasn't damaged immediately, 4-6 weeks after the event, strange things will start happening or not happening with appliances because chips on the the board were damaged and start to fail. I tell all my customers to check into WHOLE HOUSE SURGE PROTECTORS--you can buy them at Lowe's or Home Depot and, your power company might install them on your house for a little extra on the bill each month--money well spent!

whats the model no?

please go here on pc, this tells you how to reset bosch dish washer. baubilt.com/?p=1318 This tells in full detail. God-Bless you all!

Code 24 means your drain is plugged or running slow

heater??????

Control

Hi, what's the model number? Thx