Top 20
Bosch Exxcel WFX 3267 Front Load Washer - Page 9 Questions & Answers
Anyone help me. Have a Bosch aquatak 1200 plus but no power going to motor fuse changed no difference. Plz help
chek if you have power by the on of button , if tere is power , chek transformer , if there is power on both sides , if motor have a capacitor , test it don,t get shocked ,u can test it with a meter , or it must be abel to make a spark, look for lose wires , chek if tere is belds on the motor and the drum ,chec if the pully on the motor axes is not lose , that the motor run but not the drum ,chec the power lead and the male plug that go to the wall , find the book let in dex for ansers lastly phone your electrical persone , but don ,t get shoked ! please hope it helped
How to fix Bosch Classixx 6 washing machine pump fault
My Bosch Classixx 6 Express 1200 washing machine suddenly developed three faults at the same time, with no fault codes. The water pump, fill and spin cycles all stopped at the same time. I found that the one of the pump wires had come loose from the connector plug. This will not only stop the drum from emptying but will prevent the machine from filling and also stops the spin cycle. These are all interconnected and controlled by the water pump, which has to be working and connected. Hope this helps. My 11 year old machine is now working perfectly.
,
MY BOSCH LOGICXX8 WHILE WASHING KEEPS COMING UP ITH F37 AND WONT STOP EVEN WHEN IVE UNPLUGED IT PLEASE HELP
The Bosch Logixx 8 washers indicate an F37 error when the temperature sensor is defective. Sometimes this can happen if the incoming water line gets too cold. If that is the case, pressing the temperature button twice may help. (You should see a snowflake in the top left corner of the LCD screen.) Otherwise try thawing the water pipes.
If the problem isn't cold/frozen water lines, then the temperature sensor is faulty, the wiring between the sensor and the control board could be damaged or the control board has a problem getting the temperature information. Check the sensor and the wiring first. Often there is a sheet inside the washer (near the control board) with the expected resistance across the sensor and other parts. Unplug the washer before testing.
Please add a comment with the model of the washer for a parts diagram or price list. If your washer is under warranty, contact Bosch about the error.
I hope this helps.
Cindy Wells
My bosch front loader washing machine is does not finish a program. Instead, an E05 error code appears.
For Bosch washing machines, the E05 error indicates no water coming into the machine, the water being siphoned out of the machine as it enters or the water comes in too slowly. Do you hear the water coming into the washing machine? If you hear the water running in and draining out, check the height of the outflow tube. If it is below the water level in the washer, lift it up to stop the water being siphoned out.
If no water is entering the washer, make sure that the water supply shut-off valves are open. Next, check for kinks in the supply hoses. Turn off the shut-off valves and disconnect the supply hoses. Check if the filters are clogged on either the washing machine inlets or at the shut-off. Some supply hoses are designed to stop a flooding problem by restricting the flow if they are damaged. Try connecting the hoses to the shut-off valves. Then place a bucket under the hose, check the water flow rate by turning on the water to each hose individually. Alternatively, just replace the hoses.
If the inlet supply is fine but no water enters the machine, then the problem is probably with the washer's inlet valve opening and closing. You can test this with a multi-meter; most washers have a trouble-shooting sheet inside the machine (near the control board) which indicates the expected voltages and resistances. The valve will need to be replaced.
If water enters the washing machine without draining out, then the problem is with the sensor that determines the water level. Some machines use a pressure switch. In that case, the air tube can be clogged. That's often simple to blow out. Alternatively, the tube could be damaged. Sometimes the switch or sensor is faulty or the wiring could be damaged. In rare cases, the control board is not getting the correct signals.
Please add a comment with the model number of the washer, if you'd like me to search for a parts list or diagram. I hope this helps.
Cindy Wells
Not finding what you are looking for?