Top 20 Bosch Exxcel WFX 3267 Front Load Washer Questions & Answers


If the machine has been moved recently, ensure that it is level and not leaning forward. Pull the dispenser completely out (pull as far as it will go, then press down on the blue section in the fab cond compartment to fully remove) make sure it is clean and free or fab cond and powder build up. Following the diagram, check that part 0412 is clear (this can be done when the drawer is out by putting some water in the dispenser manually and seeing if it flows quickly. A baby bottle brush can be used to clear it, if it is blocked.769ae95c-736a-45f2-a40f-6dd121e32863.png

Bosch Exxcel WFX... | 54 views | 1 helpful votes


If the motor is not spinning, you may have a burnt out motor or faulty Motor Control Board. Else, if the motor is spinning, fix the belt from the motor to the drum.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Bosch Exxcel WFX... | 243 views | 0 helpful votes


Hi from retired Englishman in SW France,
(no promises but it's worth trying this!)
I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to spin or release the door lock if there is any water still left inside.
Here are my complete and generic guidance notes for checking both the drain motor filter and the drain motor ;-0)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Bosch Exxcel WFX... | 151 views | 0 helpful votes


Hi,There are quite a few solutions available here:http://www.fixya.com/tags/error_f04/page-5
Regards,Icom1

Bosch Exxcel WFX... | 298 views | 0 helpful votes


This sounds like a bad main control board. Try unplugging it for 10 minutes then replug an try again. If you get the same results replace the main controller.

Bosch Exxcel WFX... | 151 views | 0 helpful votes


You can either take the dispenser out , unclip top part of dispenser, then prise out the insert which has the holes fof the water, or if dispenser is in place ,with a small screwdriver, gently prise the fabric conditioner downwards and with an old toothbrush , remove the black mould

Bosch Washing... | 364 views | 1 helpful votes


https://washingcodes.com/bosch-dishwasher-error-codes/
Try the above. They are listed as knowing your brand codes.

Bosch Washing... | 77 views | 0 helpful votes


What is a Bosch Max 800??

Bosch Washing... | 45 views | 0 helpful votes


chek if you have power by the on of button , if tere is power , chek transformer , if there is power on both sides , if motor have a capacitor , test it don,t get shocked ,u can test it with a meter , or it must be abel to make a spark, look for lose wires , chek if tere is belds on the motor and the drum ,chec if the pully on the motor axes is not lose , that the motor run but not the drum ,chec the power lead and the male plug that go to the wall , find the book let in dex for ansers lastly phone your electrical persone , but don ,t get shoked ! please hope it helped

Bosch Washing... | 38 views | 0 helpful votes


First check the if there's a debris screen on the got water inlet, as it may be plugged. Make sure the hot water volume is good. With hot water hose disconnected at the washer, put end of hose in bucket and turn on hot water. You should get 20L (5Gal) a minute minimum. If water volume is good and screens are not plugged, then likely the hot water inlet valve has seized. Could be both hot/cold valves are integrated so both get changed. Not a bad idea to just do them both if separate hot/cold valve.
If you know how to use a volt meter you could check power at the hot valve to make sure its not a control issue or swap the control wires and select a warm temp cycle. If you get cold water then its not a control issue.(dont forget to put wires back)

Bosch Washing... | 65 views | 0 helpful votes


Bosch dishwasher error code e09. Icon E 09indicates issues with the heating element. Most likely, the device has burnt down and needs to be replaced, but it's not so simple. The flow-through heater in thedishwasher differs from the heater in the washing machine.

Bosch Washing... | 90 views | 0 helpful votes

Not finding what you are looking for?
Bosch Exxcel WFX 3267 Front Load Washer Logo

18 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Carmen Mikulic

Level 2 Expert

415 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Washing Machines

  • Bosch Washing Machines

Most Popular Question

leak detergent drawer

  • Washing Machines
Loading...