Jacuzzi Kitchen Iron Black Finish Undermount Sink - Answered Questions & Fixed issues

Is it possible they cut the hole wrong?Call the installer.Did you pay them?Take them to small claims court. If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

The sink should be physically mounted with clips if it is not cast iron, otherwise a cradle made of wood is usually the route I go.
Feel free to contact me with any questions. Brandon Wiese - [email protected] - http://.www.StoneRepairman.com

Just a note here that this phenom does happen just like toilet tanks just crackin while you are sitting in the living room watching TV. There is no explanation for it.

While I personally would not expect any manufacturer of anything to pony up 2 years after their warrenty expired, to each his own. I do however believe it would be good public relations if they gave you a replacement.

I understand your anger and frustration but I ask to to remember that getting a Ford Mustang that is a total lemon from the factory does not equate to all Ford Mustangs being lemons or that everything Ford makes is a lemon.

Godd luck and I hope they come through for you.

No the weight of the disposal will not separate the sink from the granite. When they set the sink they put wood on the edge under the sink to hold the weight of the sink. You will not have a problem.

use a color back wax found in auto parts store to restore

If you have a 3" hole I would definately say that is a special order faucet, But if 3" is a typo you can get what are called "cockhole covers" to cover the hole you're not using. What i usually do is, find a faucet that will use the 3 holes and install a soap dispenser, filtered water spigot, or a instant hot water spigot to fill the fourth hole.
If 3" is not a typo you might try to contact a granite countertop co. or call Jacuzzi and install a larger plate that will cover large holes and have new (smaller) holes drilled for a standard faucet

hope this helps

Are we concerned about the distance between the bottom of the sink and the bottom of the cabinet?

I have installed a lot of disposals on under-mount sinks and I have found the the Badger company has a 1/3 hp unit that is quite short. It may seem a bit small but we need to remember that disposals are not made to chop wood.......1/3 is plenty strong for a person who uses their head when shoving food sown it. Their 1/2 hp unit might also work.

They are available at Lowes and Home Depot for around $60.

Hope this helps

Your sink is clearly made to be undermounted. No trim ring available. With all of the choices now available for sinks and faucets I would recommend that the jacuzzi sink be removed and that you select a new sink and faucet set to your liking. good luck.

The flashing on/off light in a Jacuzzi whirlpool bath may indicate an issue with the control system, and it's important to address the problem to ensure the proper functioning and safety of the whirlpool bath. Here are some general steps you can take to troubleshoot the issue: 1. Check the Power Supply: - Ensure that the whirlpool bath is receiving power. Verify that the circuit breaker for the whirlpool bath is not tripped, and check for any loose or disconnected power cords. 2. Inspect the Control Panel: - Examine the control panel for any visible issues, such as loose or damaged wires, connectors, or buttons. Ensure that there is no water or moisture present in the control panel area. 3. Reset the System: - Some whirlpool baths have a reset function. Turn off the power to the unit, wait for a few minutes, and then turn it back on. This can sometimes reset the control system. 4. Refer to the User Manual: - Check the user manual that came with your Jacuzzi whirlpool bath for specific information on troubleshooting and resetting the control system. The manual may provide insights into the meaning of the flashing light and how to address it. 5. Contact Jacuzzi Customer Support: - If the issue persists and you cannot find a resolution through the manual, contact Jacuzzi customer support or the manufacturer for assistance. They may be able to provide guidance on how to troubleshoot and resolve the issue. 6. Professional Inspection: - If you're not comfortable or able to identify and fix the issue, it's advisable to seek assistance from a qualified professional or a technician experienced in Jacuzzi whirlpool bath systems. They can perform a thorough inspection and diagnose and repair any electrical or control system problems. It's essential to prioritize safety and follow proper procedures when dealing with electrical components and water. If you're uncertain or if the troubleshooting steps don't resolve the issue, it's best to seek professional assistance to avoid potential hazards.

they twist out

Maybe these folks can help they stock allot of Jacuzzi parts.

Can't Find It?

Send us a picture Text a photo: 305-321-3420 https://www.guillens.com/catalog/shop/Jacuzzi/Bath/Repair-Parts/Control-Boxes/mfr-3BU?pagenum=1

yes the are and parts are available on line.

Hi, Please attempt to start the jacuzzi without any water and see if it functions. Then you can fill the jacuzzi up to 1/4th with water and check if it continues to run. If so, continue to one half full. If this jacuzzi breaks down at these water levels, then you'd need to call the manufacturer to advise on what part needs to be changed to get everything working again. Thank you.

No, replace the whole thing. That is bad design and inferior parts. Ask Moen to replace it under warranty. They might say No, but then again, they might know of a fix or if they had a bad batch of plastic parts.

Hello, Several things can cause this problem- if you post a picture of the inside of the tank so we can have a good look at how the fill/stop mechanism operates that would be great. We could more than likely identify some type of problem and solution. Not all flush/fill mechanisms are not the same but thats surely where your problem is UNLESS its in your water lines. I would love to help you just please provide photos and as much information as you can. Good luck! Mr.Mike

pump -impeller failure /bearings /motor failure

Contact the Dealer and seek qualified tech service. Risk of electric shock/***** You should not take the risk but have a QUALIFIED SERVICEPERSON perform the work.

There may be a video but you should be able to tell by looking at it too big screw under tank holds valve on big screw under tank holds valve on see: https://reviewmotors.co/jacuzzi-dual-flush-toilet-repair-parts

If there is power to the unit, most likely it will need to be replaced. Check for reset button, and check the fuses before replacing the unit.

Should be one on the motor and also check to see if there is a GFCi somewhere too. Could be around where the jacuzzi switch is.