20 Most Recent Bosch WFMC 3200 Front Load Washer - Page 8 Questions & Answers

A Buzzer is not a Bell and a Bell is not a Buzzer. The little gizmos used these days are sonalerts a cross between the two. Looks like a cube of sugar with slots in it.

first of all, start with you close the door,you put the set on and continue please

Hi, shut off your water at the fill hoses first. Remove the hoses and check the screen in the hose for debris/mineral deposit build up. Visually check the inlet screen of the valve as well while you're at it. Reconnect them and insure you water taps/valves are completely open. Hope that helps, Good Luck :)

If something smells it is overheating and heading towards total breakdown.....even catching fire!
. Stop using the machine and have it checked by a local qualified techo for that brand.

try cleaning out the drain pump/filter/outlet hose.

Look for a kinked drain hose. Make sure drain hose is not plugged. Remove drain hose from washer and inspect drain outlet on washer is not plugged. Stick your finger inside and feel for any clothing fabric ect blocking drain line. The washer may have a built-in screen that is plugged. You may need to remove the back cover of the washer and inspect drain hoses for any kinks or blockages.

Be careful to allow the new door gasket to relax for at least a day before doing the installation. Take it out of the box and lay it out in a circle to help get any kinks out of it.

Also, when installing the new gasket, go slowly when stretching it over the edges of the washer drum and the door edge, being extra careful to make sure you align the gasket properly on the washer. You might want to take a digital picture of the existing gasket before you remove it, so you can refer to it when reinstalling the new gasket.

Some models have a port for the water inlet on the gasket, if your's does, install the gasket over the inlet first, then move onto the rest of it. If your's doesn't have a inlet port opening in the gasket, just be sure you have the gasket orientation correct.

Replacing a door gasket/boot is one of the things that most homeowners can do themselves and save yourself having to pay for a technician.

Here's a exploded line drawing of your washer, so you can see the parts and order of installation before you dive into taking things apart.

http://www.searspartsdirect.com/partsdirect/getSubComp.pd?modelNumber=WFMC3200UC-01&productCategoryId=0153200&brandId=1794&modelName=WASHER&diagramPageId=00002&componentDescription=DOOR%20ASSEMBLY&documentId=P0507026&backToLink=Return%20to%20Sub%20Components%20list

Hope you find this Very Helpful and best regards!

Loosen screws on hinge, be care door can be heavy.

hi, this is a drain pump motor issue. i would check the wires leading to the drain pump and the control board. make sure the pump wires are connected and the control board wires as well. if the wires are connected, this will rule out a communication problem and confirm pump failure.

You can also do a break point test with a multimeter on the control board to make sure the control board is working correctly.

Concerning the locked door(washer locked)**. if the door is locked, this may be a control fault. test the door lock mech for its operational value to confirm this as well.

look at the back , where the drain hose is, the pump is on the other side,then, just lay machine down on its side, you will see it

hi

The drain line is probably clogged. Maybe that a sock or other piece of clothing get between the clothes tub and the outer tub that holds the water. In this case it may then get into the drain hose that's attached to the pump.Remove the hoses from the pump and pull the item out. In case it clean there, check the outer tub port- open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then,try to remove the clothing through the port.
Draining problem is very common in Bosch washers. However,chek this easy steps.

1)Remove the white circular plate, located on the bottom left. Push a small screwdriver or needle through it and simultaneously rotate the plate clockwise.
2)Open the drain valve. Rotate the circular black handle counterclockwise. Beware of residual water.
3)Clean it. Re-assemble in reverse order.

Bosch is an excellent washer. Don't be discouraged by this simple maintenance issue.

also chek this sites
http://www.washerhelp.co.uk/diy-repair-help_3.html

http://www.wikihow.com/Fix-a-Washer-That-Will-Not-Drain-Its-Water-Before-Going-Into-Spin-Cycle

http://www.associatedcontent.com/article/818989/washing_machine_help_will_not_drain.html

hope u will b helpfull
regards

This is known as a Torx style screwdriver. Most appliances use either a size T-2 or T-3. I hope this helps you.

I have the SAME problem as of TODAY!!!
What are you going to do?
Mine is filled with soaking clothes & water.

I'm sorry ,no; the silicone rubber used in washers is a special blend and, is formulated just for ***********-in-law's machine

Checked plug fuse?

just pop it off with a small srewdriver and yes you can get to the fluff filter through the round cover
when you open the filter there will be about two litres of water come out beware

It all come in one kit: plastic front cover and boot gasket.
Part # 246270.
Manufacture warranty for Bosch washer 1 year from day of purchase.
For assistance with your Bosch home appliance
or to order spare parts
1-800-944-2904
MON - FRI ~ 5AM - 8PM PST

Also you can buy from here:
http://www.marcone.com/
http://www.repairclinic.com/SmartSearch/smartsearch.aspx I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

start on the door side of the appliance put the top of the circle in first this should allow you to stretch the spring a little to make it go on
its a pain and it kills the tips of your fingers try not to overstrech it because it will fall off all the time