Bosch Axxis+ WFR 2460 Front Load Washer - Answered Questions & Fixed issues
Pump Blocked - Cannot open/remove cap
Sometimes it just takes brute force to open the pump cap. Try wiggling a bit from side to side; if an odd-shaped item is lodged in there, it can really be tough (but possible!) to open.
Bosch Axxis WFR 2460 Front Washer Drum/Cycles Not Working
hi sounds like the motor brushs are worn down,some bosch models you can change them without removing the motor ,but others its best to remove it,they just twist out,and to refit use a small blade flat blade screwdriver to tuck tab in,thanks
Error 16
Check your solenoid valves if the coils are healthy.
Not spinning
Axxis+ WFR 2460 Front Load Washer This washing machine tutorial will show you what to do if
the washing machine does not drain or empty the water out this repair was done
on a Bosch, Neff and Siemens type appliance.
Thanks for using FixYa - a 4 THUMBS rating is appreciated
for answering your FREE question.
WFR 2460 Front loader
We went through the whole "clean the soap dispenser" deal and results were the same. Exploratory surgery revealed that the Prewash hose (for lack of better term), which connects from the top of the drum housing to the right side of the dispenser drawer (facing the machine)was completely clogged with gunk. Especially strange since we don't prewash hardly anything, ever. The hose that connects the bottom of the detergent dispenser with the side of the drum housing did have a lot of buildup, but I do not believe it was the cause because this was only happening on the rinse cycle. I also found the flow meter was frozen up.
WATER WONT SHUT OFF
Once the
water comes into the system the WATER LEVEL SENSOR - normally a pressure
switch- must activate at the preset/chosen level to give the signal to the
program controller to switch on the motor. What is most important for the motor
to start functioning is that the door switch must be ON when the door is shut
or this will be an error for starting the motor for rinse and wash.
Test a
pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8
WATER WONT SHUT OFF
. Once the
water comes into the system the WATER LEVEL SENSOR - normally a pressure
switch- must activate at the preset/chosen level to give the signal to the
program controller to switch on the motor. What is most important for the motor
to start functioning is that the door switch must be ON when the door is shut
or this will be an error for starting the motor for rinse and wash.
Test a
pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8
Bosch washer #2460 signas that water tap is
I am not sure why but there are 2 posts for your question. This is a duplicate of my original answer:
If you have checked the hoses and screens then the most probable failure is the inlet water valve. I suspect that one of the electrical water valve solenoids has failed. If you using cold water try a warm or hot wash. If your using hot or warm try a cold wash. I am not sure on this washer if there is a mixing valve but may front loading washers have mixing valves that mix hot and cold water simply to help dissolve the HE type soaps. If changing wash temp makes no difference then a continuity check for inlet water valve coil resistance will have to be performed with an inexpensive ohm meter. If there is no continuity the solenoid has failed and the inlet water valve will have to be replaced. This unit appears to have 2 inlet water valves one for hot and cold and one for just cold that is used for diluting soap. You will need to check all 3 solenoids for continuity. The inlet water valves are items 5 and 6 of this picture:
http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=192773&pkw_=basket&model_id=5110159&NewWindow=1You can find replacement parts here::
http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5110159&diagram_id=192773#d192773Let me know if you need more assistance. Kelly
Bosch WFR2460 washer---we also had
Hi joecci,
It looks like the Door Lock may be faulty, but here is a few things you should consider looking at first:
1) Is the door closed properly?
2) Have you tried giving it power straight from the mains, the door lock needs the correct power before it functions correctly?
I believe one of the above things will resolve the problem, let me know if it does?
Regards
JEDEMEYER1
Not finding what you are looking for?