Top 20 Bosch Axxis+ WFR 2460 Front Load Washer Questions & Answers

Check the drain pump

hi sounds like the motor brushs are worn down,some bosch models you can change them without removing the motor ,but others its best to remove it,they just twist out,and to refit use a small blade flat blade screwdriver to tuck tab in,thanks

Does the tub turn at all when you start it?

Sam
Melbourne Domestic Appliances
Text 0424395512

did you use resolve? i had a problem when i used it, it took the colour from one and mixed with an other.lol

Is the belt wore out and slipping? Check this first.

Hey there, welcome to Fixya! The above answers were pretty helpful, did you fix your problem with them? Did you check the manual for further instructions? You can find a PDF copy here: Bosch Classixx 5 Manual

Sound like the pump is clogged here a link http://laundry.manualsonline.com/manuals/mfg/bosch/axxis+_wfr_2460.html page 37

Check your solenoid valves if the coils are healthy.

. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Test a pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8

Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Test a pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8

this sound like the brushes in the motoror it might be a fault on the pump

this video will show you how to take the fron of a bosch washing machine

If you have checked the hoses and screens then the most probable failure is the inlet water valve. I suspect that one of the electrical water valve solenoids has failed. If you using cold water try a warm or hot wash. If your using hot or warm try a cold wash. I am not sure on this washer if there is a mixing valve but may front loading washers have mixing valves that mix hot and cold water simply to help dissolve the HE type soaps. If changing wash temp makes no difference then a continuity check for inlet water valve coil resistance will have to be performed with an inexpensive ohm meter. If there is no continuity the solenoid has failed and the inlet water valve will have to be replaced. This unit appears to have 2 inlet water valves one for hot and cold and one for just cold that is used for diluting soap. You will need to check all 3 solenoids for continuity. The inlet water valves are items 5 and 6 of this picture:http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=192773&pkw_=basket&model_id=5110159&NewWindow=1You can find replacement parts here:: http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5110159&diagram_id=192773#d192773Let me know if you need more assistance. Kelly

F18 error code means that the filter is blocked.

Look around for a propeller shaped part, it should be able to spin freely. If not, remove the debris so that it is unblocked.

Hope this helps (remember to rate and comment this answer).

Bosch Maxx This video will show you how to change the pump washing machine Please remember to subscribe to our YouTube channel for all appliance tutorials a 4 THUMBS rating is appreciated for answering your FREE question. And don't forget to like us on facebook

I am not sure why but there are 2 posts for your question. This is a duplicate of my original answer: If you have checked the hoses and screens then the most probable failure is the inlet water valve. I suspect that one of the electrical water valve solenoids has failed. If you using cold water try a warm or hot wash. If your using hot or warm try a cold wash. I am not sure on this washer if there is a mixing valve but may front loading washers have mixing valves that mix hot and cold water simply to help dissolve the HE type soaps. If changing wash temp makes no difference then a continuity check for inlet water valve coil resistance will have to be performed with an inexpensive ohm meter. If there is no continuity the solenoid has failed and the inlet water valve will have to be replaced. This unit appears to have 2 inlet water valves one for hot and cold and one for just cold that is used for diluting soap. You will need to check all 3 solenoids for continuity. The inlet water valves are items 5 and 6 of this picture:http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=192773&pkw_=basket&model_id=5110159&NewWindow=1You can find replacement parts here:: http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5110159&diagram_id=192773#d192773Let me know if you need more assistance. Kelly

Hi joecci,

It looks like the Door Lock may be faulty, but here is a few things you should consider looking at first:

1) Is the door closed properly?
2) Have you tried giving it power straight from the mains, the door lock needs the correct power before it functions correctly?

I believe one of the above things will resolve the problem, let me know if it does?

Regards

JEDEMEYER1