20 Most Recent Bosch Axxis+ WFR 2460 Front Load Washer - Page 3 Questions & Answers

I would imagine that you accidently disconnected the water level pressure switch and the machine never new the water level had been reached. However a "pop" is a bad thing electrical and I hope you didn't fry your control panel. The fuse shoud be on the back of the unit by the power cord. Obviously unplug it before servicing it.
good luck!

Hi from retired Englishman in SW France,
A quick and easy way to find out which tray is which is to pull the detergent drawer out just so that you can see into it. Start a pre-wash and see where the water runs in, then advance to the main wash and observe. Finally start a rinse cycle and where the water goes in is where the conditioner/softener goes.
In a few cases I have come across, the pre-wash tray shares with the conditioner/softener part but the pre-wash powder goes in the front and the softener in the back.

Now, methinks you could do with a manual ;-0)
You will need to type into your search engine/web browser '(make) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount. During the process you will be asked for the actual model number!
You could also try the manufacturer's web site direct.

If these have assisted you please score accordingly.
Thanks and good luck!
John C

Have you tried cleaning the filter next to the drainage pipe? (Lower left near Door).
The compartment is opened by turning it anti-clockwise and pulling it out (Be wary of water coming out!).

Most likely a small obstruction (Coin, Rocks, Toothpick... and in past experiences a "thong") might be blocking your impeller.

Hope this helps, if it doesn't let me know and I'd get technical ;-)

Kind Regards

* If you found this solution helpful, please rate 4 thumbs up and leave a small testimonial. :-)

Yes its very semple takes about 20min.

The 03 error code is the drain. Disconnect the drain hoses and check for blockages. If no blockage "time" the drain interval. If it's more than 6 minutes it's the pump. Also make sure you're using the correct type of soap so the ball check valve on the bottom of the outer drum isn't getting fouled with excessive suds. Also disconnect the drain hose from your house plumbing and let it free flow on it's own. This will tell you if the block is in your plumbing, and not in the machine. Assuming that your filter is clean.

Pl rate me ‘very helpful’ for the free help!

Make sure the child lock is not on...

Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing Machine not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Remove hose at washer connection and check screen filter not blocked with grit from pipes. Check screen at tap end also. If both clear, machine may need water valve replaced.

It says the 1st compartment going left to right laundry detergant and stain remover, the middle is for the soaking agent, and the last one is for fabric softner. I hope that helps!

You can download the manual online and I found the info on page 12 of the manual.

Did you try and look up the manual on line? It is available on page 12 it tells you were to load it. It is a pull out in the front of the machine with three compartments.

Motor carbon brushes/ motor need checking

Hi,

Press the Start/Pause button and hold down ( 5 Seconds ) until the Start/Pause indicator light flashes.

When the Pause is Displayed, the Child Lock is temporarily deactivated.


You could Read All the Instruction on Child Lock from Manual. Download the Manual from :-

http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man

Type the number and click on download now. You need to have Acrobat Reader to View this.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Try selecting the spin prog, if there is any water in the washer, this will drain it, and you should be able to open the door.
Please leave comment as to whether this solved your prob or not.
Thankyou.

I thought I had replied to this post before, however, you should have a button on the control panel showing 600 or 1200.
Just press the button for the correct spin speed.
Please rate my solution.
Thanks.

This would be your drain pump on this Bosch. Contact us at:

http://www.fixya.com/repair/d499389-accurate_appliance_repair_service with your model number and we will send the correct pump out right away!
I love Bosch! Thanks, Ella

If bottom front comes off its on l/h side low...

Remove the top cover, and release the door catch from inside the front of washer.
Please rate my solution.
Thanks.

I just had the same problem last week Aug 1 2009
on our WFK 2401 purchased in 2001

If you hear no motor spinning when it should then it's something
with the motor. If you hear motor spinning, esp spin cycle, but
the drum doesn't spin, then probably broken belt ($30 part).

Since I work on cars (this is very much like an alternator+belt) and wanted to avoid a $100 service call (just to come to house) and
at least try for a quick fix before buying a new washer, I opened the back, confirmed belt looked ok, so tried
replacing the brushes in the motor, and it worked.

For a good description on how to do this see
http://dossy.org/2007/05/lots-of-miles-on-our-bosch-wfk2401uc-washer-motor/
I took some pics, and time permitting will post more details
to this dossy site to help fellow owners.
I purchased the brushes at partstap.com for $50 (incl tax+ship)