Kohler Toilet - One Piece with Ingenium Flushing System - San Raphael by - Page 9 - Answered Questions & Fixed issues
I have a K4632-AA which usually works just fine
Toilets seem to run on their own because the water in the tank is seeping our past the seal that was designed to keep it in the tank inbetween flushes. Commonly called flappers, they go by seals, tank balls discs. etc. The K4632 requires a flat seal from Kohler. The actual part number is 1059291, however Kohler may only sell this as part of a kit by a different number with pieces not truely needed in your circumstance.
You should contact them at 1-800-4KOHLER, navigate the prompts, and talk to a service member. You may have to do some research in your area to find a retail or wholesale business that will order this for you. There are circumstances where, with some parts, Kohler will send the parts free to your doorstep. No promises on this one. I have put a link below that will give you a complete parts explosion for your reference.
http://www.kohlerserviceparts.kohler.com/ServicePartsPage.aspx?DocumentID=28e40a91273141a5b63e28ad7230d6a5&ModelID=e9143848792b4415a62b4e384caeb856
9/6/2012 5:08:03 PM •
Kohler Home
•
Answered
on Sep 06, 2012
•
4,401 views
Particles come out of jets
Are the particles like white chunks? If yes, I was told to get calcium and lime remover and add it to the water and let the tub run for 30 minutes. Once this is done, drain and then refill tub and run for another 30 minutes to get the lime and calcium remover out of the system. This should help.
8/9/2012 7:44:51 PM •
Kohler Home
•
Answered
on Aug 09, 2012
•
130 views
Water level in toilet bowl is low
adjust fill valve turn the water off to the toilet push down on the tension clamp and pull the valve up higher then resecure
7/29/2012 7:12:48 PM •
Kohler Home
•
Answered
on Jul 29, 2012
•
213 views
Refill valve
This happens when the seal on the flood tube is leaking and there is an imperceptible leak into the bowl.
7/13/2012 12:20:41 AM •
Kohler Home
•
Answered
on Jul 13, 2012
•
131 views
HOW DO I FIX A LEAKY FAUCET
make sure that the handles r not loose if so get them sung if that wont work u may have to replace the guts sometime the ball value doesnt close all the way.
4/26/2012 7:00:38 PM •
Kohler Home
•
Answered
on Apr 26, 2012
•
148 views
Stuck kohler toilet seat
most modern toilet seats are removed by opening plastic tabs on the upper rear of the seat and turning the screws counter clockwise while holding the retaining nuts underneath the bowl.there has to be access and if not ,you could drill them out from the top using a small drill bit and slowly working your way up to bigger bits till the heads of the bolts are removed.
11/21/2011 4:59:39 PM •
Kohler Home
•
Answered
on Nov 21, 2011
•
290 views
Toilet tank dose not fill
Go to an ace hardware or walmart and buy a replacement kit for the inside of the toilet. They do not cost that much and should be able to solve your problem just follow the diagram to install, it is fairly simple. Parts wear out and this will save you a lot of money from getting a plumber
9/27/2011 12:11:33 AM •
Kohler Home
•
Answered
on Sep 27, 2011
•
129 views
The toilet flushes but it
Hi!please kindly check your fill valve if it is working correctly.I thought the problem is in your fill valve.Kindly adjust the floater of your fill valve.
8/24/2011 9:35:41 AM •
Kohler Home
•
Answered
on Aug 24, 2011
•
944 views
I have a kohler commode,
I would go to walmart and buy a new toilet seat and make sure it fits an elongated toilet, they are like 20 bucks or less
8/22/2011 8:05:33 PM •
Kohler Home
•
Answered
on Aug 22, 2011
•
219 views
Jet streams whirpool not working
you have been hit by power surge. most likely the problem is in the control box that controls the pump. Need to call local plumber or service company to take a look at the system.
Verify that all circuit breakers are on and stay on after being reset before calling service tech.
US Parts Center
8/22/2011 6:09:40 PM •
Kohler Home
•
Answered
on Aug 22, 2011
•
216 views
No power to the jets on our KOHLER bathtub
Check the main breaker, check the GFCI that the pump is plugged into. Make sure you have power to the outlet that the pump is plugged into.
if you have power to that point we need to find out how you are turning the pump on.
Can you take the pump out and plug it into another outlet to make sure the pump is good?
8/19/2011 2:02:13 PM •
Kohler Home
•
Answered
on Aug 19, 2011
•
185 views
When I fill my tub
this happens sometimes when the leads under the tub get a bit corroded. Get under the tub and find the studs and screws that are at the end of the low water sensor wires and clean them up with some emery cloth then reinstall them.
this should get you back up and running again.
US Parts Center
8/18/2011 10:45:43 PM •
Kohler Home
•
Answered
on Aug 18, 2011
•
280 views
Installed a new Kohler wethworth toilet. Every 2-5
Water level in tank might be set too high, allowing water to drain out the overflow. lower the water level in the tank. (I am assuming the flapper is ok. Flapper may have a protective disc, which should be removed after installation.)
8/8/2011 11:50:16 PM •
Kohler Home
•
Answered
on Aug 08, 2011
•
147 views
Tank is full but continues
either the fill valve is running and water is draining into the bowl via
the overflow tube in the tank or the flapper is bad (or foreign matter)
and it is allowing water to escape into the bowl slowly...causing the
fill valve to run every few minutes or so. i just sent this to your email too. hope this helps but if you need anything else just text me here:)
7/28/2011 7:25:57 PM •
Kohler Home
•
Answered
on Jul 28, 2011
•
947 views
Not finding what you are looking for?