Kohler Toilet - One Piece with Ingenium Flushing System - San Raphael by - Page 8 - Answered Questions & Fixed issues

watch the mechanism after you flush. If the opening that lets water into the bowl does not close snugly, tiny stream will continuously flow. Make sure it closes properly.

Prelude: My toilet had the same problem a few times. I managed to clean it out because the pipe is somehow connected to the downstairs drainage pipe in my house. What fixed the toilet clog was going to the source of the problem and pouring extremely powerful hair clog remover chemicals in it (I did have to open all the windows and get the pets as far away as possible and wear a mask). After the specified amount of time waiting, I went to go flush and it worked. **Answer**: I would recommend doing the same thing but only if everyone in the house is gone for 1 hour. Also I would air it out by leaving windows open, not first floor doors or windows though. It can be deadly if inhaled for extended periods of time. The more powerful the cleaner, the better the results but the deadlier it can be if inhaled. Try this. My second guess is that it may be the plug inside the toilet's tank. You should check to see if it is working properly. Try flushing with the lid off and watch the plug to see if it is working properly.

Fill valve blocked. Try moving float valve arm up and down. DON'T FORCE. Just check range of motion I’m happy to help further over the phone at https://www.6ya.com/expert/robert_24775b73ca70da93

it's a motor problem. maybe u need to change the motor.

Most hardware stores carry a good variety of fittings. (Plastic, Brass and iron). Just be sure the leak is the fitting and not just the hose connections. Don't forget to turn the water supply off before cutting the lines.

Which suction cover do you have? Can you email us a photo of the cover you have so we can match it up for you?email to [email protected] Parts Center

yes. Why so much moisture? There shouldn't be any unless you have hot water filling the tank or a spray of water shooting out. Check it out.

Here is the manual for your Samsung Galaxy Note 10.1. Just click on the PDF icon and wait a little for it to load.http://blog.clove.co.uk/2012/08/16/samsung-galaxy-note-10-1-gt-n800-user-guidemanual/

need more information about what kind of control you are using to turn the tub on/off.does it turn off when you can get it turned on?Rod US Parts Center888-521-6183

When a bath pump turns on but does not move any water it is usually because there is an Air Lock and needs to be released.Try this.

• Fill the tub with water
• Turn the pump on
• Unthread the discharge pump union until water starts to squirt out
• when this happens you should hear a big 'swoosh'

if the bath pump starts to discharge water through the jets then you have solved the problem.Rodus parts center888-521-6183

Mold on your jets can come from a variety of places but due mostly to the bacteria in the tub.There are several kinds of cleaners to use in the meantime once you get your trim clean so you can prevent what you are experiencing.Take the trim off and clean them in your sink. DO NOT put them in the dishwasher as it is too hot and will ruin your trim.Here is a link to our site that has different options for cleaning the pipes and keeping the jets from getting yucky.Maintenance ProductsRodUS Parts Center888-521-6183

Your valve inside the tank has worn down and not allowing the water to stop running. Does the water run over the top of the overflow. If so, then adjust your inlet water to a lower level so it will cut off. If that is ok, then likely the flapper is worn out and needs to be replaced.

The workings of a bath jet...From the inside of the Bath there is a wall fitting that threads from the inside of the tub into the jet body located on the outside wall of the tub.If the jet is leaking at this point behind the tub then you should take the wall fitting out of the tub and put a small bead of 100% RTV silicone around the flange of the wall fitting and reinstall it.If however, the leak is from the PVC piping going into the jet then you will need to replace the jet.RodUS Parts Center888-521-6183

Try a pumice stone they work great & can make a toilet bowl look brand new, there with the cleaning supplies in any store.D :)

The chances that is problem you are experiencing is related to the suction cover is extremely remote. The suction assembly doesn't have anything to do with the tub motor operating.The issue is most likely with the motor not working or the air switch in the motor malfunctioning.What does the control look like that you use to turn the pump on/off?Is it an air button or an electronic switch?

Yes, contact Kohler and they have a site you can watch that should be helpful.

Has anything non soluble gone down toilet. If plunging vigorously doesn't work, you may have to take up toilet to see the bottom part. Does any of the water go out of the bowl. Does it eventually go down on its own.

EntsJust replace the assembly and be done with it . It sounds like minerals in the water are building up in the lines and components. It is hard to remove it all.

need to be level 3 then go to that thingy in your nest and go to that door on the left and press mission 1 but you need 1 dosh.How get 1 dosh:got to your nest and press the bincard thingy finally press that stamp thing then you got 1 dosh.from lolo

Look on the internet or call the company.