Kohler Toilet Seat - Elongated Front Quiet Close Quick Release - Cachet by - Page 8 - Answered Questions & Fixed issues

make sure that the handles r not loose if so get them sung if that wont work u may have to replace the guts sometime the ball value doesnt close all the way.

replace the flapper with a new one. There are universal flappers at your local home store that will work for you.

if its leaking from bottom of toilet on the floor. its the wax ring that may be bad, if it does this when flushing it is either cracked or the wax ring under toilet is bad.

most modern toilet seats are removed by opening plastic tabs on the upper rear of the seat and turning the screws counter clockwise while holding the retaining nuts underneath the bowl.there has to be access and if not ,you could drill them out from the top using a small drill bit and slowly working your way up to bigger bits till the heads of the bolts are removed.

Go to an ace hardware or walmart and buy a replacement kit for the inside of the toilet. They do not cost that much and should be able to solve your problem just follow the diagram to install, it is fairly simple. Parts wear out and this will save you a lot of money from getting a plumber

Hi!you better change your shower door because its hard to rectifies that kind of door

Hi!please kindly check your fill valve if it is working correctly.I thought the problem is in your fill valve.Kindly adjust the floater of your fill valve.

they usually go on the bottom between toilet ant the wing nut fastener

I would go to walmart and buy a new toilet seat and make sure it fits an elongated toilet, they are like 20 bucks or less

you have been hit by power surge. most likely the problem is in the control box that controls the pump. Need to call local plumber or service company to take a look at the system.
Verify that all circuit breakers are on and stay on after being reset before calling service tech.

US Parts Center

Check the main breaker, check the GFCI that the pump is plugged into. Make sure you have power to the outlet that the pump is plugged into.
if you have power to that point we need to find out how you are turning the pump on.
Can you take the pump out and plug it into another outlet to make sure the pump is good?

this happens sometimes when the leads under the tub get a bit corroded. Get under the tub and find the studs and screws that are at the end of the low water sensor wires and clean them up with some emery cloth then reinstall them.
this should get you back up and running again.

US Parts Center

Water level in tank might be set too high, allowing water to drain out the overflow. lower the water level in the tank. (I am assuming the flapper is ok. Flapper may have a protective disc, which should be removed after installation.)

either the fill valve is running and water is draining into the bowl via the overflow tube in the tank or the flapper is bad (or foreign matter) and it is allowing water to escape into the bowl slowly...causing the fill valve to run every few minutes or so. i just sent this to your email too. hope this helps but if you need anything else just text me here:)

If your certain water is not escaping under the flapper and leaking out into the sewer then the fill valve is bad and needs replaced. If it stays running but doesnt fill then the flapper, or flush valve will need replaced. These are in all hardware stores and come in many types and variaties, all you have to do is match up the old with a new set or get the person in the plumbing dept to get you a suitable replacement. The shuddering is the water under pressure leaking past the fill valve because it is not opening as wide as it should. These all wear out over time and need replaced every few years. Changing out the fill valve should remedy your problem. Here is a link to what you need but you will be better off getting it from your local harware dealer so they can make sure it is the correct part for your toilet.
http://weddleplumbing.com/index.php?route=product/product&product_id=117

In 2008 I bought the Memoirs model that Lowe's was selling. I've had multiple tank/bowl gasket leak problems. When I went to get a replacement gasket this weekend, Kohler had changed the style of the tank/bowl gasket assembly in the current Memoirs model that Lowes sells. I wonder if this is because the old gasket assembly is known to be defective and prone to leaking?

When I called Kohler, it took two customer service associated, but I was granted a WHOLE NEW TOILET with the new style of tank/bowl gasket assembly. I just had to have the receipt for the (3 yrs ago) purchase. Kohler e-mailed a letter for a replacement toilet within about 15 minutes and before the end of the day, I had a whole new toilet in my bathroom.

I'm not a contractor. Just an average homeowner, so I can't say for sure that the old style (large, black, plastic rectangle on the bottom of the tank and a rather thin gasket ring) was defective or not. (At first Kohler offered only a replacement tank, but after hearing the number of times both I *and* plumbers have replaced the gasket, they did authorize the replacement of the entire toilet.)

REPLACE THE WASHER INSIDE THE FAUCET IF YOU CAN FIND THE RIGHT ONE.
REGARDS.
PLZ. RATE THIS

Another remedy if you can't find the same lugs or stoppers, is go to any hardware or home depot store and get those little plastic stoppers that are felt or adhesive back that is used for the bottom of kitchen chairs so as not to scratch harwood floors, you can use them fo substitute . Also they make small round 1/4 inch plastic little bumps used for home slider window stops. Hope this helps you get that toilet seat up and running , or is that down and running :) mike

Indeed, that sounds like it has suffered fro ma power surge. You can look up on Google maps in your area for a qualified repair man, or you can try and tackle the job yourself, though if you do not have experience with 220v services I would strongly advise against this, as it could lead to a fire and or electrocution.

NEED TO ADJUST FLOAT . Turn screw clockwise 1 to 2 full turns at top of float rod.