Kohler - Toilet - One-piece - Gabrielle - K14257-WS-47 - Page 7 - Answered Questions & Fixed issues

The chances that is problem you are experiencing is related to the suction cover is extremely remote. The suction assembly doesn't have anything to do with the tub motor operating.The issue is most likely with the motor not working or the air switch in the motor malfunctioning.What does the control look like that you use to turn the pump on/off?Is it an air button or an electronic switch?

Yes, contact Kohler and they have a site you can watch that should be helpful.

Has anything non soluble gone down toilet. If plunging vigorously doesn't work, you may have to take up toilet to see the bottom part. Does any of the water go out of the bowl. Does it eventually go down on its own.

EntsJust replace the assembly and be done with it . It sounds like minerals in the water are building up in the lines and components. It is hard to remove it all.

need to be level 3 then go to that thingy in your nest and go to that door on the left and press mission 1 but you need 1 dosh.How get 1 dosh:got to your nest and press the bincard thingy finally press that stamp thing then you got 1 dosh.from lolo

Look on the internet or call the company.

Toilets seem to run on their own because the water in the tank is seeping our past the seal that was designed to keep it in the tank inbetween flushes. Commonly called flappers, they go by seals, tank balls discs. etc. The K4632 requires a flat seal from Kohler. The actual part number is 1059291, however Kohler may only sell this as part of a kit by a different number with pieces not truely needed in your circumstance.

You should contact them at 1-800-4KOHLER, navigate the prompts, and talk to a service member. You may have to do some research in your area to find a retail or wholesale business that will order this for you. There are circumstances where, with some parts, Kohler will send the parts free to your doorstep. No promises on this one. I have put a link below that will give you a complete parts explosion for your reference.

http://www.kohlerserviceparts.kohler.com/ServicePartsPage.aspx?DocumentID=28e40a91273141a5b63e28ad7230d6a5&ModelID=e9143848792b4415a62b4e384caeb856

Are the particles like white chunks? If yes, I was told to get calcium and lime remover and add it to the water and let the tub run for 30 minutes. Once this is done, drain and then refill tub and run for another 30 minutes to get the lime and calcium remover out of the system. This should help.

sounds like you need a flapper they are all the same for the most part

adjust fill valve turn the water off to the toilet push down on the tension clamp and pull the valve up higher then resecure

This happens when the seal on the flood tube is leaking and there is an imperceptible leak into the bowl.

DO LIKEI DID USE SOME WATER AND AC BASE TYPE OILCUT POWER FIRST THEN PUSH BOTTON IN AND OUT

make sure that the handles r not loose if so get them sung if that wont work u may have to replace the guts sometime the ball value doesnt close all the way.

replace the flapper with a new one. There are universal flappers at your local home store that will work for you.

if its leaking from bottom of toilet on the floor. its the wax ring that may be bad, if it does this when flushing it is either cracked or the wax ring under toilet is bad.

most modern toilet seats are removed by opening plastic tabs on the upper rear of the seat and turning the screws counter clockwise while holding the retaining nuts underneath the bowl.there has to be access and if not ,you could drill them out from the top using a small drill bit and slowly working your way up to bigger bits till the heads of the bolts are removed.

Go to an ace hardware or walmart and buy a replacement kit for the inside of the toilet. They do not cost that much and should be able to solve your problem just follow the diagram to install, it is fairly simple. Parts wear out and this will save you a lot of money from getting a plumber

Hi!you better change your shower door because its hard to rectifies that kind of door

Hi!please kindly check your fill valve if it is working correctly.I thought the problem is in your fill valve.Kindly adjust the floater of your fill valve.

they usually go on the bottom between toilet ant the wing nut fastener