Top 20 Kohler - Toilet - One-piece - Gabrielle - K14257-WS-47 Questions & Answers

Fill vale needs to be replaced.

It sounds like you need a 10" or 8" rough-in toilet bowl.

adjust your water level float if you have one or turn your inlet for water up higher.

The foam gasket stays on the inside of the tank, the only part that gets pushed through the hole is the hard plastic threaded part, then you add the rubber washer and the nut from underneath.

I would take the flexible connector from the toilet and while directing the flow into a bucket open the angle stop, If the flow is normal you may have debris in the fill valve if the flow is wimpy there could be a defective angle stop or flex connector

Follow the instructions on p.12 of the following pdf:
http://www.geberit.com.au/web/appl/au/wcmsau.nsf/files/usr-pdf-Geberit_Outlet%20Valves.pdf/$file/Geberit_Outlet%20Valves.pdf
Basically, push down the 'full-flush' (big) side of the flush button and look at the side of the remaining (small) side of the button. There is a little slot that allows you to pull the small button out. You can then pull out the big side of the button which exposes a screw that allows you to pull the lid off.
Hope that helps.

try;
-plunger
-toilet snake
-you may need a plumber if these do not fix your problem.

some carpet cleaning machines have little balls that stop the water at a certain hight in the machine. could have come out and thats what is plugging the toilet

Hi. There are toilets designed to accept a round seat and there are other toilets designed to accept an elongated seat. The primary difference is that the round seat fits a round bowl and the elongated seat fits an elongated bowl.

I recommend that you return the elongated seat and exchange it for a round toilet seat. good luck

I have never heard of a toilet that needs an electronic reset, but it appears it is as simple as just disconnecting the power for 10 minutes. It does sound though are yours has a failing flush valve. I managed an airport lounge and we had dozens of electronic toilets and we had to keep a box of spares for them and just put new parts in them including complete control boards. We also kept a box of batteries. https://www.google.com/search?q=kohler+hatbox+toilet+factory+reset ..

Lift and pull the lid forward lift up and disconnect the lift lever from the chain.

I would take it back for another toilet.

https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1095641_2.pdf

Kohler has good support. You can view the diagrams for that unit with the link I am posting. There are no filters listed in the diagram that might need to be cleaned. There is a chance that the unit has developed a clog from hair etc in the pump impellor. The flange may have come loose and is allowing air in the suction side of the pump too. Kohler has online chat and support numbers you can call too. K-1357-RA ' Devonshire 5-Foot Whirlpool with Apron and Right Drain ' KOHLER

The only batteries are in the docking station. If the remote is attached to the docking station, take that off and set it aside. Next, carefully lift the docking station up and out from the mounting bracket. Look at the back of the docking station, push the two tabs outwards (away from each other) simultaneously to open the battery compartment cover. Replace the batteries (4 AAs) in the correct orientation. Reinstall the cover. Then replace the docking station on the mounting bracket and put the remote back on the dock if desired. These directions are shown in the Homeowner's Guide (without the service parts) available on the product page: https://www.us.kohler.com/us/veil-intelligent-comfort-height-skirted-one-piece-elongated-dual-flush-toilet/productDetail/toilets/1120267.htm . Scroll down to the Installation section to find the link to the document. The current link to this guide is https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1226974_5.pdf . I hope this helps. Cindy Wells

Rent a multimeter and test your connections. As well as checking the breaker

https://www.us.kohler.com/us/catalog/maintenanceLanding.jsp

I just posted an answer here, but don't see it. ??

The brand of toilet doesn't matter. You need a product that cuts calcium and lime. It may take some soaking and scrubbing. Once you get it clean, use the product regularly. CLR makes a line of products: https://clrbrands.com/en-US/Products/CLR-Household/CLR-Calcium-Lime-Rust-Remover

I don't know this specific tub, but here's the pictoral. The button (90105) should come out of its base, held by friction of O ring. This should allow you to disconnect the pressure line. If you are looking to replace the complete assembly, likely you will need a basin wrench to reach nut (65157). Here are links to Kohler, specific to this tub. https://www.us.kohler.com/us/catalog/svg_viewer.jsp?productId=415928&diagram=3 https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1010564_5.pdf