Kohler - Toilet - One-piece - San Raphael - K3467-NG - Answered Questions & Fixed issues

Try cleaning the surface of the drain hole where the flapper fits. There might be crud causing it to not seal. Sometimes the flapper itself is not large enough (or too large) to properly fit the hole. If no good you might try weighting the flapper. Not easy to do. You'll have to pull the flapper, dry it completely find the right adhesive place the weight just right. And hope that works. Good Luck...

the flapper is either stuck open or the fill valve shut off is broken

Hi,

Click here

And yes... you will pay plenty for them... cause they are Kohler...

heatman101

it's the fill valve that squeaks. Sometimes a slight adjust to the water level works, but most of the time it needs to be replaced

Sounds like the flapper is leaking water out of the tank. The flapper is the rubber valve that comes up and down every time you pull the flush lever. It is located in the tank at the bottom in the center. Very cheap part to replace.. Just turn the water off to the stool, take the top of the tank off, hold the flush lever down until all the water is out of the tank, reach in to the tank, disconnect the flush chain from the flapper, and disconnect the flapper arms holding to the stem. You can buy a flapper at any hardware store even at wal mart. Hope this helps.

Not a major task, though perhaps accomplished in an uncomfortable position. If the bolts are stripped, and won't come off, and you can't get a saw under the rim to cut off the bolts, take a drill and drill down through the bolt from on top.

This will weaken the plastic bolt enough in order for you to break it off. Another way is to use a Dremel tool with a grinding wheel to cut off the bolts.

Check here additional installation details: onlinecatalog/pdf/1070416_2 pdf

Hope helps.

The flapper on these toilets is a water saver. The water saver flappers can be replaced with a standard flapper and I have found this will help considerably. The flapper is located in the tank at the center bottom. It is the part that flaps up and down when you pull the lever.

There has to be...see if the plastic cover pops off to expose the bolts

There's probably a small crack or very small hole in the overflow tube. Turn off the water supply to the toilet and empty the tank. Look very carefully for any crack or hole in the tube. You can replace the tube, but that requires taking the tank off or repairing the leak with a sealant.

Reset the float also the flapper could be deformed or it's seat may have a chip or bump.....

Okay. The question is a bit lacking in details. Password for what? Password ON what? Where was the file stolen from? Who stole the file? What is the file content. What is the file extension (the bit after the file name and the period file_name.what)? All questions need to start 'make model (what it is)' first 3 words. And then a clear question. For the 13 people that have tagged this 10 year old question, it is better to post your own question. ..

I have never heard of a toilet that needs an electronic reset, but it appears it is as simple as just disconnecting the power for 10 minutes. It does sound though are yours has a failing flush valve. I managed an airport lounge and we had dozens of electronic toilets and we had to keep a box of spares for them and just put new parts in them including complete control boards. We also kept a box of batteries. https://www.google.com/search?q=kohler+hatbox+toilet+factory+reset ..

Lift and pull the lid forward lift up and disconnect the lift lever from the chain.

https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1095641_2.pdf

I would take it back for another toilet.

Kohler has good support. You can view the diagrams for that unit with the link I am posting. There are no filters listed in the diagram that might need to be cleaned. There is a chance that the unit has developed a clog from hair etc in the pump impellor. The flange may have come loose and is allowing air in the suction side of the pump too. Kohler has online chat and support numbers you can call too. K-1357-RA ' Devonshire 5-Foot Whirlpool with Apron and Right Drain ' KOHLER

just turn the water valve down some

Rent a multimeter and test your connections. As well as checking the breaker

We had a problem with phantom flushing. Call Kholer. They will send redesigned battery holder and top of flush unit for free. Seems to have fixed the issue.

The only batteries are in the docking station. If the remote is attached to the docking station, take that off and set it aside. Next, carefully lift the docking station up and out from the mounting bracket. Look at the back of the docking station, push the two tabs outwards (away from each other) simultaneously to open the battery compartment cover. Replace the batteries (4 AAs) in the correct orientation. Reinstall the cover. Then replace the docking station on the mounting bracket and put the remote back on the dock if desired. These directions are shown in the Homeowner's Guide (without the service parts) available on the product page: https://www.us.kohler.com/us/veil-intelligent-comfort-height-skirted-one-piece-elongated-dual-flush-toilet/productDetail/toilets/1120267.htm . Scroll down to the Installation section to find the link to the document. The current link to this guide is https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1226974_5.pdf . I hope this helps. Cindy Wells