Kohler - Toilet - One-piece - Santa Rosa - K3323-52 - Page 4 - Answered Questions & Fixed issues
I changed out my Kohler shower diverter cartridge
did your old diverter have a shut off knob on it? if so you may have not noticed it leaking, -what causes that is the existing shower faucet may have been mounted to high from the spout below -or the pipe going down from existing fixture to the tub faucet spout pipe may not be at least 3/4", -if its 1/2" it will always do that
9/12/2017 7:15:10 PM •
Kohler Home
•
Answered
on Sep 12, 2017
•
2,891 views
KOHLER TOILET
either flapper needs replacing or water level float set to high
8/19/2017 4:35:51 PM •
Kohler Home
•
Answered
on Aug 19, 2017
•
53 views
I have a Kohler cistern,
you can try to remove it or you can go to a plumber supply shop and get a new level controller
faster easier and gives another 10 years of service
you may have to remove the unit from the cistern to get enough force applied to turn the cap so the job is half done anyway
8/5/2017 9:52:52 PM •
Kohler Home
•
Answered
on Aug 05, 2017
•
208 views
I have a Kohler 1.6
Never heard of such a thing. You'd better contact Kohler on this one, bro. . .
7/3/2017 12:42:47 AM •
Kohler Home
•
Answered
on Jul 03, 2017
•
3,895 views
My whirlpool tub is not working. Nothing happens
first check the air switch hose that connects to the "button"
Open the access for the pump there should be 1/4" poly tubing (probably clear) that connects to the pump motor. It just slides over a barbed nipple usually located somewhere on the back of the pump housing opposite the pipe connections. Make sure it is in place properly. If it is in place then look else where. The tubing also connects to the back of the air switch "button". This button connection rarely fails, especially if the tub was working and now does not. But if the tub is newly installed and may have disconnected during installation. this connection is probably going to be difficult if not impossible to verify since it is usually concealed after installation.
Some pump motors have resets some do not. If it does it probably is on the very back of pump opposite the pipe connections.
Also check to make sure that any electrical outlets in the bathroom, or any where in a nearby radius of the tub, to see if they have "GFI" reset buttons and make sure that they havn't tripped by pushing in the button between the plug-ins named "reset". Usually the circuit for the pump will be tied into one of these switches to add ground fault protection to the circuit.
If your pump is not working after checking these things it may be dead. Does your pump "hum" after pushing the button? Do you smell any type oder around the pump that would suggest a "burnt motor"?
If the pump is dead you will have to replace it.
Come back here and post more if your problem isn't solved. Or ask how to find and replace a new Whirlpool pump.
Hope you figure it out. T. Wood CFE Plumbing
12/14/2016 9:21:01 AM •
Kohler Home
•
Answered
on Dec 14, 2016
•
20,248 views
My toilet is broken?
How is it broken provide details as there are many issues you could have need to know how to answer your specific problem
5/27/2016 11:47:31 PM •
Kohler Home
•
Answered
on May 27, 2016
•
370 views
How do I prevent a toilet refill tube from slipping out of the overflow pipe?
Hello there,if you check on line you'll see there is either a funny looking piece of metal that hooks to the tube and refill pipe.They also sell a circular piece to fit over fill tube with a hole in the centre to push your tube into it.First off check and see if these didn't fall off into tank.If not Canadian tire, homedepot can help with this just have makers name of toilet or model
5/8/2016 11:31:28 PM •
Kohler Home
•
Answered
on May 08, 2016
•
804 views
Both the flush buttons have jammed in the flush position.
To open the assembly, first line up the flush buttons with the float mechanism. This aligns tabs on the button mechanism with a slot on the mating surface allowing you to 'pop' the button assembly off with the help of a screwdriver. It will also prevent breaking off the tabs. If you break off the tabs, the button assembly will not lock in place when you reassemble it (speaking from experience).
2. Carefully pop off the button assembly with the help of a screwdriver.
3. Disengage the lever from the valve assembly by carefully prying with a screwdriver (see video).
4. Pop off the lever from the axle on button assembly and remove.
5. With some fine grit sand paper or emery cloth, polish the casting marks off of the axle.
6. Reassemble the mechanism. Assembly is the reverse of disassembly.
http://www.instructables.com/id/How-to-fix-leaking-Water-Ridge-dual-flush-toilet-f/
12/21/2015 9:59:55 PM •
Kohler Home
•
Answered
on Dec 21, 2015
•
1,304 views
My Kohler K4493-AA occasionally produces a high-pitched whine like a smoke alarm. Flushing stops it, but then the sound comes back later. Any ideas?
Typically it's one of two things. Either there is debris (Sand, gravel or hard water deposits) under the seal diaphragm inside the fill valve or the diaphragm has deteriorated. Shut off the water to the tank, take the cap off of the fill valve and remove the diaphragm. If the diaphragm has deteriorated, replace it Kohler #83143. Otherwise, rinse it off, turn the water on just a bit to let it bubble over the top of the fill valve and rinse out any debris. Then with the water trickling, put the diaphragm back in and replace the top assembly. When all is secure, turn the water back on to full.
11/30/2015 6:31:55 PM •
Kohler Home
•
Answered
on Nov 30, 2015
•
390 views
Sewer smell drain
are there any floor drains in the room and an unused bathtub or shower? if so the water may have evaporated from the trap and allow the sewer gas smell. try pouring water into all the drains and see if it is still happening. more elaborate problem may be a broken vent stack in a wall.
4/9/2015 4:22:29 AM •
Kohler Home
•
Answered
on Apr 09, 2015
•
535 views
Not finding what you are looking for?