Top 20
Northstar Pressure Washer 3000 PSI Questions & Answers
I have a northstar pressure
Sounds like the trigger is not closing, best to strip it down and check operation. Probably siezed in the open position.
10/15/2017 12:03:04 AM •
Northstar...
•
228 views • 0 helpful votes
Adjust soap injector
If it connect to the outlet pipe/lance then it operates on SUCTION similar to blowing across the top of a beer bottle to make a noise. If thats the case it is a matter of blockage and ventilation of the soap bottle to allow air to enter as the soap is sucked out by the water flow.
10/23/2015 6:03:29 PM •
Northstar...
•
316 views • 0 helpful votes
Need help in getting Honda engine on NorthStar pressure washer to run.
Could be low water pressure I have found.Also, I purchased a can of "stuff" at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump....the pump could be frozen up...I have a rotating nozzle which I bought...and it had frozen up...this stuff works
8/31/2012 6:57:59 PM •
Northstar...
•
194 views • 0 helpful votes
Will not start
do you have spark?try starting fluid that will tell you if its a fuel problem
8/5/2012 8:45:49 PM •
Northstar...
•
83 views • 0 helpful votes
Engine will not run with
You will need to remove the carburetor and clean. Be sure to clean the high speed jet. This jet is the bolt that holds the fuel bowl on. Remove and clean the small holes in the sides of bolt. You will need a small piece of wire or bread tie just remove the outer covering and run this through the holes. Some have a hole in the bottom and smaller hole in the threads towards the top. Clean with carburetor cleaner and blow with compressed air. Try cleaning the jet first and if this doesn't work then clean and rebuild entire carb. Hope this helps.
7/23/2011 11:39:32 PM •
Northstar...
•
316 views • 2 helpful votes
Im not getting any pressure (other than hose
Your problem is going to be with the brass fitting with the spring that you have discribed. This fitting is called an unloader valve, this valve is designed to by-pass the pressure that the pump has built up so you don't damage the pump when you release the trigger. There should be a nut on the end of this valve try turning it in some if this doesn't work try turning it out. It is usually set at the factory but sometimes they either don't get set or they are bad. You also could try to remove and clean. re-install with a light coat of white lithium grease. Hope this helps, let me know how you make out.
7/6/2011 7:35:20 PM •
Northstar...
•
243 views • 0 helpful votes
There is water squirting out
If this hole has threads then it might be the soap inlet. If water is shooting out under pressure you may have an obstruction in the hose/handle. Try removing the hose and running the washer and see if the water flows out the connection. If the hose ends up being the problem a visual inspection and cleaning of all inlets and the handle should clear it.
If the water coming out of the hole is low/tap line pressure then I think your bypass *(or unloader) valve is stuck in the bypass position.
A stuck unloader just needs to be unstuck and lightly cleaned. A light coating of silicon grease wouldnt hurt either!
Get the manual for this pump and see how to open/remove the unloader valve.
6/4/2011 6:10:16 PM •
Northstar...
•
347 views • 0 helpful votes
I asked your experts a question on Saturday March
I am sorry you have had a poor experience on this website. I would be happy to answer your question if you can post it in this thread or if you would prefer to contact me directly at 800.247.8103. I am a certified pressure washer service technician for Landa and Karcher and have over 4 years of experience fixing pressure washers for 8 hours a day.
Aron Kerr
Landa Northwest
www.landanw.com
3/8/2011 1:45:21 AM •
Northstar...
•
248 views • 0 helpful votes
Hi, I have a qusstion.
the short answer is "no" and I have to ask, why would you want to, if you are thinking that you could use it to provide high pressure air to blow stuff off your deck, it won't work, the pump requires liquid in order to get enough pressure to push the water at high pressure
3/22/2011 11:50:43 PM •
Northstar...
•
114 views • 0 helpful votes
Can i use karcha hose
Yes. Both brands use M22 (22MM) hose fittings. You will need to check that the Karcher hose is rated to a high enough pressure for your washer, especially if it is a thermoplastic hose as they tend to be rated for 2500 PSI.
Sincerely,
Aron Kerr
Landa Northwest, Inc.
www.landanw.com
3/1/2011 3:22:28 PM •
Northstar...
•
91 views • 0 helpful votes
Does the machine need an oil change, if so how
i would change the oil every 100 hours or six months in the engine.
and would change the oil in the pump every 12 months.
to change the engine oil,look for a 12mm or 13mm bolt at the base of the motor.
it should be at the front of the engine.undo bolt & drain oil into a container.
tighten bolt up & fill engine with new oil.
12/9/2010 11:21:43 PM •
Northstar...
•
531 views • 0 helpful votes
Not finding what you are looking for?