20 Most Recent Husqvarna Craftsman 36cc, 16 In. Gas Chain Saw - Page 9 Questions & Answers

The system is not recognizing that you are in the seat for some reason. Ck the wiring from the switch could be broken/disconnected somewhere. plus read this fellows last reply.... https://lawnmowerforum.com/threads/husqvarna-z254f-dies-as-when-move-control-arm.66970/

There are a few potential reasons why your Kawasaki engine on your Husqvarna P-ZT 54 may be losing power when the blades engage. Here are a few possible causes and solutions:

Low engine speed: If the engine speed is too low, it may not be able to power the blades effectively. Try increasing the engine speed by adjusting the throttle.

Dull blades: Dull blades can put extra strain on the engine, causing it to lose power when the blades engage. Sharpen or replace the blades as necessary.

Belt tension: If the belt that drives the blades is loose or worn, it may slip when the blades engage, causing the engine to lose power. Check the belt tension and replace the belt if necessary.

Dirty air filter: A dirty air filter can restrict the airflow to the engine, causing it to lose power. Check and clean or replace the air filter as necessary.

Fuel issues: If the engine is not getting enough fuel, it may lose power when the blades engage. Check the fuel filter and make sure the fuel tank is clean and free of debris.

If none of these solutions work, it may be best to have a professional mechanic take a look at your mower to diagnose and fix the problem.

Here https://www.google.com/search?q=+Husqvarna+GTH2248XP+tractor+snow+blower ..

If your Husqvarna rz46i zero turn mower was acting like the transmission was slipping and now it won't move at all, there may be an issue with the transmission or drive belt. Here are a few things you can check:

1. Check the drive belt: Make sure the drive belt is properly attached and tensioned. If it's loose or damaged, it can cause slipping or failure to move. Replace the belt if necessary.
2. Check the transmission oil level: Low oil level in the transmission can cause slipping or failure to move. Check the oil level and add oil if necessary.
3. Check the transmission filter: A clogged transmission filter can cause the transmission to slip or fail to move. Replace the filter if it's dirty or clogged.
4. Check the transmission itself: If none of the above steps resolve the issue, there may be a problem with the transmission itself. It may be necessary to have a professional technician inspect and repair the transmission.

It's also possible that there could be an issue with the mower's hydrostatic transmission or drive system. If you're unsure of how to diagnose or repair the issue, it's best to contact a professional technician for assistance.

It's possible that the loose release switch could be causing the issue with the mower only running in reverse. When the release switch is not properly engaged or disengaged, it can cause the mower to think it is in neutral, which may prevent it from moving forward. You may want to try tightening or adjusting the switch to see if it helps. However, there could also be other issues with the transmission or drive system that are causing the problem, so it's important to thoroughly check all components and consult the manual or a professional if necessary.

If the engine mount set screw is not holding the engine in place and a new screw pushed out through the threads, it's possible that the threads on the engine or the screw are damaged. One solution could be to try tapping the mounting hole with a larger size tap to create new, tighter threads. Another option could be to use a thread repair kit, such as a helicoil, to create new threads in the mounting hole. It's also important to ensure that the screw being used is the correct size and type for the engine mount. Using the wrong size or type of screw can cause it to strip or push out through the threads. If the problem persists, it may be necessary to consult with a professional or the manufacturer for further assistance.

There could be several reasons why a Husqvarna K970 shuts down at full throttle after it warms up. Here are some possible causes:

1. Fuel system problems: The carburetor may be clogged or dirty, causing a fuel delivery problem. This can cause the engine to stall when it is running at full throttle.
2. Air filter problems: A dirty air filter can restrict the flow of air into the engine, causing it to run too rich and stall at full throttle.
3. Ignition system problems: A faulty ignition system can cause the engine to stall under load. This could be due to a failing spark plug or a bad ignition coil.
4. Overheating: The engine may be overheating, causing it to shut down when it reaches full throttle. This could be due to a cooling system problem or an issue with the engine itself.
5. Mechanical problems: There could be a problem with the engine or other mechanical components, such as the piston or crankshaft.

If you are not comfortable troubleshooting the problem yourself, it is best to take your K970 to a qualified service technician for diagnosis and repair.

If your Husqvarna backpack blower starts well but starts to act like it's not getting enough gas when you put it at 3/4 speed, there could be a few potential issues causing this problem. Some possible causes include:

1. A clogged fuel filter: The fuel filter is responsible for removing dirt and debris from the fuel before it reaches the carburetor. If the filter is clogged, it can restrict fuel flow and cause the engine to run poorly.
2. A clogged carburetor: The carburetor is responsible for mixing fuel and air to create the combustion that powers the engine. If the carburetor is clogged, it can restrict fuel flow and cause the engine to run poorly.
3. A dirty air filter: The air filter is responsible for removing dirt and debris from the air before it reaches the carburetor. If the filter is dirty, it can restrict airflow and cause the engine to run poorly.
4. A problem with the fuel line: If the fuel line is kinked, pinched, or has a leak, it can restrict fuel flow and cause the engine to run poorly.
5. A problem with the spark plug: A faulty spark plug can prevent the engine from running properly, it can cause misfire and the engine to run poorly.

It's recommended to check the fuel filter, carburetor, air filter, fuel line, and spark plug. Clean or replace them as necessary. It's important to consult the operator's manual for specific troubleshooting instructions and diagrams for your blower model, as the location and procedure may vary depending on the make and model. It's also important to consult the operator's manual for safety instructions, and to make sure you have the correct parts for your blower. It's recommended to seek the help of a qualified technician if you are not familiar with this process.

Also check fuses, they are located on the left hand side of the Machine. They are accessed by tilting the seat Forward. They are ?at pin Fuses of the same type used in automobiles. There are two fuses with ratings and functions: 20 amp Primary Fuse 7.5 amp mower deck coupling

Removing the deflector on a Husqvarna YTH2348 lawn tractor can vary depending on the specific model, but the general process should be similar. Here are the steps to remove the deflector on your Husqvarna YTH2348 lawn tractor:

1. Park the tractor on a level surface and set the parking brake.
2. Locate the deflector on the tractor. It is usually located at the front or rear of the tractor, often attached to the hood or the deck.
3. Locate the fasteners that hold the deflector in place. These may be screws, clips, or pins, depending on the model.
4. Using the appropriate tool, remove the fasteners that hold the deflector in place. A screwdriver or pliers may be needed.
5. Carefully lift the deflector off the tractor.
6. To reattach the deflector, align it with the mounting points and secure it with the fasteners.

It's important to consult the operator's manual for specific instructions and diagrams for your tractor model, as the deflector location and the procedure to remove it may vary depending on the make and model. It's also important to consult the operator's manual for safety instructions.

If the fuel bubble on your Husqvarna 125 BV blower is not priming the engine to start, there could be a few potential issues causing this problem. Some possible causes include:

1. A clogged fuel filter: The fuel filter is responsible for removing dirt and debris from the fuel before it reaches the carburetor. If the filter is clogged, it can restrict fuel flow and prevent the engine from starting.
2. A clogged carburetor: The carburetor is responsible for mixing fuel and air to create the combustion that powers the engine. If the carburetor is clogged, it can restrict fuel flow and prevent the engine from starting.
3. A problem with the fuel line: If the fuel line is kinked, pinched, or has a leak, it can restrict fuel flow and prevent the engine from starting.
4. A problem with the fuel tank: If the fuel tank is not properly sealed, it can allow air into the fuel system and prevent the engine from starting.
5. A problem with the primer bulb: If the primer bulb is not functioning properly, it can prevent fuel from reaching the carburetor.

It's recommended to check the fuel filter, carburetor, fuel line, fuel tank and primer bulb. Clean or replace them as necessary. It's important to consult the operator's manual for specific troubleshooting instructions and diagrams for your blower model, as the location and procedure may vary depending on the make and model. It's also important to consult the operator's manual for safety instructions, and to make sure you have the correct parts for your blower. It's recommended to seek the help of a qualified technician if you are not familiar with this process.

check and test the safety switches

I'm sorry to hear that your Husqvarna 125B blower isn't starting. Here are a few things you can try to troubleshoot the issue:

1. Check the fuel level in the tank. If the tank is empty, fill it with the correct fuel mixture (50:1 ratio of gasoline to oil). If the fuel is stale (more than 30 days old), drain the tank and refill it with fresh fuel.
2. Check the spark plug. Make sure the spark plug is clean and properly gapped. If the spark plug is dirty or damaged, replace it.
3. Check the air filter. A dirty air filter can restrict the flow of air, causing the engine to run poorly or not start at all. Clean or replace the air filter as needed.
4. Check the carburetor. If the carburetor is dirty or clogged, it can prevent the engine from starting. Clean the carburetor or have a professional service it.
5. Check the ignition system. If the ignition system is not functioning properly, the engine may not start. Check the ignition coil, ignition switch, and any other related components to make sure they are working correctly.

If you have tried these steps and the engine still won't start, it may be necessary to take the blower to a professional for further diagnosis and repair.

to much slack worn--wrong belt--replaced incorrectly -----their is an adjustment on the actuator pulley very slight and slight adjustment on deck brackets

MOVED YOU OUT OF CARS TO LAWN MOWER. that is lost engine power causes are bad fuel or old and bad. fuel all filters clogged,air or fuel or carb clugged up,. (gunked up from bad fuel super common) cold starts use a choke and goes super rich hiding clogged jets in carb. clean carb or replace it if all above filters and fuel good.

check linkage and bushings

https://gardentroop.com/problems-with-husqvarna-zero-turn-mowers/ This may help.