20 Most Recent Continental CE-PAC1163 Air Conditioner - Page 5 Questions & Answers

Maybe this video will help: https://www.youtube.com/watch?v=xOZGx6--B2A

Hi I'm getting e4 on my aircon daytek

Impossible to answer without 'make model (what is is)'. That should be the first 3 words in every question.

Troubleshooting ' Air Conditioning and Refrigeration

Daikin https://www.daikin.com > products > ac > services > trou... If the operation lamp still flashes, disconnect the power plug from the outlet or turn the breaker off and contact the place of purchase. Are there any objects ...

Air Conditioner Light Blinking Problem Solving Techniques ...

absolutesolutions.com.sg https://www.absolutesolutions.com.sg > news > why-my... Nonetheless, a blinking light is mostly an indicator that your unit needs to be serviced if you expect it to not only service you back but to do so efficiently.

Have model ras-17ekv-ul green operation light and orange

JustAnswer https://www.justanswer.com > HVAC Questions Jun 25, 2020 - You may have had a power failure. Try resetting the breaker. Flashing green indicates power loss. Flashing orange for outdoor circuit board ... 1 answer · Top answer: It shouldn't as long as the unit is off when you kill power. ..

Question edited for clarity. Stuck blend door actuators, stuck thermostat, or this, airlocks. https://www.fixya.com/support/r29872074-vehicle_cooling_system_no_heat ..

The compressor has overloaded. I would power it off and leave to cool for 30 minutes the power on again to start it up. If it has still got the error, call a maintainance engineer.

bad compressor

there is no rest. Item used 24VAC from hvac to power it . If 24VAC from hvac is missing thermostat will not power up and hvac will not work. You will need to call for service.

It is telling you that an error condition exists. It will be that the water reservoir needs to be emptied, or that the filter needs washing. Then turn it off and count to 20 and plug it back in. https://www.google.com/search?q=mira+cool+portable+air+conditioner+blinking+lights ..

Clamp your amprobe on the black wire on the power cord and check there.

The gas valve needs to be replaced.

I dont recomend buying that home.

Recheck all your exhaust connections and gaskets

KSM-IW30WAE-7J1M

in the manual it will show what the diagnosis code is for a F1. Clean and check the air filter

check continuity on switch

computer board has failed.

It is not the fan motor. it is most likely the computer board. can you take a picture of the unit and send it to me? text it to 3153418739

To fix code E5 on a Bonaire evaporative cooler, which typically indicates a water management issue, try the following steps:

1. Check the water level in the unit to ensure it's sufficient.
2. Inspect the water inlet valve for blockages or malfunction and clean or replace as necessary.
3. Clean the filter and pump to ensure proper water flow.
4. Reset the unit by turning it off at the power source, waiting a minute, and turning it back on.

If the problem persists, consult the user manual or contact Bonaire customer support for further assistance.

Just went through this after replacing Carbon filters. There is a 250V 15A fuse on one of the circuit boards but, by far, the more likely problem is incorrect seating of the front cover after replacing the filters. On the lower right side of the front cover is a rod which must go into the hole and engages a pressure switch that will kill power if the front cover is removed. This can be checked just by looking into the right hand side with the front cover installed. Ten second fix.

Question edited for clarity. Bad luck, and the company will get some negative advertising by your question as this will end up indexed by Google. There are some vendors for spare parts. If it is just a multicore wire that was damaged, that is available by the foot. https://www.google.com/search?q=human+touch+ZERO+GRAVITY+G+2+remote+replacement ..