Top 20 Pramac Storm 5000 Watt Generator - Page 7 Questions & Answers

In the link, diagrams and videos. HOWEVER, some of the wiring colors vary by country. I am British, so red live, black neutral and green earth. Black line, white neutral, red load and bare wire ground in north America https://www.google.com/search?q=dimmer+with+2+black+and+1+green%2C+the+house+has+3+black+%2C+3+white+3+green+and+1+red ..

Whether or not a NEMA 4 controller can be replaced with a controller that is not NEMA 4 depends on the specific application. NEMA 4 controllers are designed to withstand water and dust ingress, so they are often used in outdoor or harsh environments. If the controller is being used in an environment where it is exposed to water or dust, then it is important to replace it with a NEMA 4 controller. Overall, it is important to consult with a qualified electrician before replacing a NEMA 4 controller with a controller that is not NEMA 4. The electrician can assess the specific application and recommend the best controller for the job. If you want to look for a controller, you can visit: https://www.chipsmall.com/bigcategory/industrial-automation-and-controls.html to search for the controller you want.

bad news that gen copper windings smoke is load shorted? or no load smoke.? no told connected what. gen?>>>> to what? I bet the maker has no part for sale, china imports mostly do not. off to harbor Fright(pun) you go.

4.0 gallon if fuel tank is full.

Hi, please call your local electrician for help with performing this update as one improper step could cause damage to the building (ie short circuit). They'll probably mention something about put the lights in parallel as opposed to in series in order to allow the switch to give power to the lights simultaneously. Thank you.

The manufacturer or Google is the place to start.

PCv or crank case vents clogged. next time use locktite sealant all cause list , ,mine

1. crank case vent clogged, or PCV bad.
2. wrong seal.(or cloned seals off fleabay trash)
3. bearing on that shaft super worn and beat the seal to deathh
4. not use locktite,

like Threadlocker Red 271 super strong , but surfaces cleaned first. https://www.homedepot.com/p/Loctite-Threadlocker-Red-271-0-20-fl-oz-Specialty-Glue-209741/100371833

If you pushed the red button and it pops back out, the unit is still too hot. Wait ten minutes and try again. Here is a wee bit of additional advice offered in step by step fashion: https://disposalxt.com/how-to-reset-a-garbage-disposal/

There are some images in the link, but you might have to write to China and ask. https://www.google.com/search?q=king+bench+grinder+wiring+diagram ..

It should be recycled at your local recycling centre, used to be know as the tip or rubbish dump. It must not go in household rubbish because it is highly toxic and kills wildlife, fish and humans!!!

Try eliminating some ambiguity and describe the operation of one wall light from two switches. Don't describe the switch type just a switch location and how the wall light should behave when a switch changes.

It's difficult to understand how you want a light to operate differently from the typical set of two 3-way switches. It seems you want to control on/off from two locations using 3-ways with the addition of a.single pole to override the 3-ways. Buy that's my interpretation and may not be what you want.

Then double the circuit... so in my interpretation it would take two 3 gang boxes at each side of the bed and two more boxes elsewhere for the lamps.

you dont directly their are transfer systems that get wired into breaker panel [ automatic or manual ] other way is have a plug set up from outside to panel their are multi videos on how to hook up one on you tube

Auto idle function?

https://www.rvandplaya.com/how-to-fix-fault-code-14-on-onan-generator/ This might help you.

check breakers if ok bad board

With a light in the ceiling, one in the shower and a lighted mirror. https://www.google.com/search?q=light+up+a+bathroom ..