20 Most Recent Stanley 77 115 Intellisensor Plus Stud Sensor - Page 2 Questions & Answers

Hi Gene,

• Place the unit flat against the wall.
• Press and hold the button.
• The LED will come on for a second or two then go out.
• Slowly move the unit laterally until the LEDs come on again.
• When they top out, that is the beginning of the stud.
• When they start to go back down, that is the end of the stud.

That's about it..

Best regards
Mike

Hello,

Here are instructions to get the manual for this sensor:

Go to Stanley Support

Click on the "Knowledge Base" link.

When the window opens type 77 115 in the search block and click on "Search". (NOTE: Leave a space between 77 and 115 or this will not work.)

The Instruction manual should be on top of the list that appears.

Click on the link under the "Article Name". (77-115 Intellisensor Plus Instructions)

On the next window click on the small icon under "Format". That will open up a PDF file for you. Save it to your computer for future use.

If you have any trouble, just comment back.

Thanks for using Fixya.

You need to change detector tip sensor OR re-calibrate the unit.

Hello,

Here are instructions to get the manual for this sensor:

Go to:
Stanley Support

Click on the "Knowledge Base" link.

When the window opens type 77 115 in the search block and click on "Search". (NOTE: Leave a space between 77 and 115 or this will not work.)

The Instruction manual should be on top of the list that appears.

Click on the link under the "Article Name". (77-115 Intellisensor Plus Instructions)

On the next window click on the small icon under "Format". That will open up a PDF file for you. Save it to your computer for future use.

If you have any trouble, just comment back.

Thanks for using Fixya.

Question edited for clarity. The LED Area Light or the Unit display. The backlit display always stays on to alert you to the internal battery status, so that when you come to use it, it should be fully charged. https://www.manualslib.com/manual/2188388/Stanley-Fatmax-Pp1dcs.html?page=2&term=light&selected=1#manual

I'm having same problem... anyone know?

replace battery. Check your manual that came with unit. copy and paste Stanley fat max power it 1000a battery

Select a location that is relatively level and flat. The edge of a bench is best so that the level can be placed in the same position when the level is rotated during the calibration process. To calibrate follow below: Press and hold Calibrate button for about 4 seconds. The display will now show CAL1. Press the Calibrate button briefly again and the 1 will flash, a beep will be heard and CAL2 will be displayed. Rotate the level 180° end to end with the display still facing you whilst the level is now upside down. Place the level in the same location. Press the Calibrate button briefly one last time. The 2 will flash, a beep will be heard and the display will revert back to normal.

From the the attached photo I see that you have completely disassemble the tape. This makes the tape almost impossible to reassemble. The spring has to be back wound fully, the blade attached and retracted back into the case using the back wound spring. This requires special equipment that is not overly complicated, however not possible to make for a once off use. I have designed, built and trained operators to use this type of equipment in a production situation, however in my 35 years of experience I have never been seen anyone back wind a spring by hand. Sorry to say but the tape is ready for the trash.

It is a known issue! https://www.google.com/search?q=stanley+fatmax+powerit+1000a+wont+turn+off ..

stanley fatmax jumpstarter 1000A light wont turn off?

TAKE IT BACK TO THE DEALER

Most stud finders have a sensitivity adjustment that should be carefully adjusted per instruction manual before use. Failure to do this results in erroneous indications. If you have adjusted exactly per the instructions with the same result the unit is probably faulty.

Possible low battery.

here is the website:https://www.stanleytools.com/products/hand-tools/flashlights-lighting/spotlight/waterproof-led-rechargeable-spotlight/fl5w10and they say the warranty is 1 year:Warranty1 Year Limited WarrantyThe manufacturer, Baccus Global warrants products against defects in materials and workmanship for a period of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser ("Warranty Period").If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturer's option. Proof of purchase may be required by manufacturer. (2) Return the product to the retailer where product was purchased for an exchange (provided that the store is a participating retailer). Returns to retailer should be made within the time period of the retailer's return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. Please call 1-877-571-2391 for more information or return instructions.This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product.OOtherwise, check with the seller who sold it to your wife - If they are unwilling, and more companies seem to be going this route, go to the Manufacturer

Yes. Unless one was provided the standard is to just use an extension cord.