Electrolux EW1000i Front Load Washer - Answered Questions & Fixed issues
Bra underwire stuck
disconnect from electricity. take back panel off.you will see heater at bottom of tub held in by 1 10mm nut.disconnect wires to it. loosen this nut and pull heater out - you may have to help it with a screwdriver. you can then see into the gap between tub and drum and fish for the bra wire.
tell her not to wear bras with wires!!
1/22/2019 6:59:44 AM •
Electrolux...
•
Answered
on Jan 22, 2019
•
1,249 views
My front load washing machine is working but the water don't seem to enter.
First of all check filters in hoses & water valves, if ok then water inlet valve may be burnt out. Unplug power cord, remove top panel panel, check where 2 wires go to each water valve & check that area on valves for burning. If burnt or smells of burning, replace valve. IN SOME INSTANCES A COMPONENT BURN OUT CAN CAUSE DAMAGE TO CONTROL BOARD.
4/28/2015 6:52:50 AM •
Electrolux...
•
Answered
on Apr 28, 2015
•
118 views
Hi Ihave an electrolux EWD 1477 washer/ dryer. It keeps showing up an error E90 and starts beeping and stops working? Any ideas how to fix it
? Thanks kindly
E90 is family error code visible to the customers. It is necessary to read the error in the service mode so please proceed with the following procedure for rapid reading of alarm codes:
Press and hold down START/PAUSE and the option button nearest to the START/PAUSE button for at least two seconds!
After that the display will show one of the following errors that are more precise:
E91, E92 - Communication incongruence between main board and display board (versions not compatible). Posible causes: wirings, main board or control/disply board.
E93 - Incorrect configuration of appliance. Posible causes: Incorrect configuration data; electronic board faulty.
E94 - Incorrect configuration of washing cycle.
Posible causes: Incorrect configuration data; electronic board faulty.
E95 - Communication error between microprocessor and
EEPROM. Posible causes: Electronic board faulty.
E97 - Incongruence between programme selector and
cycle configuration. Posible causes: Faulty electronic board (Wrong configuration data).
Considering that this is a complicated fault, my advice is to contact an authorized service center.They have special equipment such as an interface that allows them to upgrade software in your appliance. If you are not doing anything on the appliance before the failure, the only thing you can check is the contacts between wiring and electronics.
Dado
2/14/2015 8:58:52 PM •
Electrolux...
•
Answered
on Feb 14, 2015
•
785 views
How to get the clothes to spin dry in Color wash mode?
Program the machine for white wash and turn down temperature and duration manually, and tune up the sentrifuge program to maximum RPM.
It helps to use a machine with large drum and minimum 1600 RPM. Large diameter of the drum is more efficient than a small diameter drum at the same RPM.
2/4/2015 8:10:17 PM •
Electrolux...
•
Answered
on Feb 04, 2015
•
86 views
Electrolux EWF1074 with Error EH0. After 2 seconds
In case of error in the mains, or like what happend today at my house, the power lines went partially down, providing too low voltage, EH0 or EH1 will occour. If you also notice that the lightning indoor is somewhat dimmed during this error, the voltage is too low.
10/22/2017 4:18:01 PM •
Electrolux...
•
Answered
on Oct 22, 2017
•
12,952 views
Error message e21
Machine tries to drain for 10 min (timeout) without emptying the tub.
Possible fault:
- drain pump
- drain filter
- drain hose
- wiring between drain pump and electronic
- electronic
Dado
1/6/2015 6:26:33 PM •
Electrolux...
•
Answered
on Jan 06, 2015
•
167 views
E4 error code on electrolux washing machine ewt 854s
E4 is the pump is blocked {not running} pehaps a hair pin or clothing wires get stuck
fully drain it and take the filter out
and clean it
these error codes are similar to candy
youll get an idea from this video
https://www.youtube.com/watch?v=kzhlvB2LjXg
11/28/2014 10:28:35 PM •
Electrolux...
•
Answered
on Nov 28, 2014
•
3,250 views
Is there a reset switch on Electrolux washer
Hey friend, thank you for the post!
I understand you are looking for a reset button on your Electrolux washer. The best way to reset your appliance would be to disconnect power from it for ten minutes, you can do that by unplugging the appliance or flipping the household circuit breaker. I hope that information is helpful. -Matt
8/1/2014 1:59:34 PM •
Electrolux...
•
Answered
on Aug 01, 2014
•
3,076 views
Error 027
check the filter at bottom of machine is not full of crap and if its clear check the sump hose under the machine sometimes socks get into it
7/22/2014 8:48:00 AM •
Electrolux...
•
Answered
on Jul 22, 2014
•
178 views
E31 error code on electrolux washing machine
Good Afternoon Friend,
I understand that you are receiving an E31 error code on your Electrolux washer, model# EW1000i. In researching the model number you provided, I show that this was manufactured in the UK. For North American washers, I would suggest resetting you appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. You can try this, and if it does not work, I suggest contacting the manufacturer directly, for further assistance. They should be able to tell you what the E31 means, as well as assist in clearing it. Hope this is helpful.
-Best Regards-
6/12/2014 1:11:25 PM •
Electrolux...
•
Answered
on Jun 12, 2014
•
2,379 views
What is error code e13
Good Afternoon Friend,
I understand that you are receiving an E13 error code on your Electrolux washer, model# EW1000i. In researching the model number you provided, I show that this was manufactured in the UK. For North American washers, I would suggest resetting you appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. You can try this, and if it does not work, I suggest contacting the manufacturer directly, for further assistance. They should be able to tell you what the E13 means, as well as assist in clearing it. Hope this is helpful.
-Best Regards-
WP
6/2/2014 2:36:20 PM •
Electrolux...
•
Answered
on Jun 02, 2014
•
1,456 views
Not finding what you are looking for?