20 Most Recent Frigidaire fex831cs stacked washer&dryer 220 volts - Page 4 Questions & Answers

A LOCAL REPAIR SERVICE

Could be cycle timer failure

PROBABLY A BAD CONTROL BOARD

Frigidaire Washer/Dryer Combo: Model GCET1031FS2 Parts ...

www.repairclinic.com > ProductDetail

Frigidaire Washer/Dryer Combo Model GCET1031FS2 Parts. Frigidaire ... If the dryer overheats, the thermal fuse blows to cut off power to the dryer. If the thermal ... ..

Could be a cycle timer issue

Part of normal operation

Select a shorter wash cycle

Try disconnecting power for awhile to allow it to "reset".

The E9F code indicates the pump is clogged.

Possibly water level sensor failed

Sorry to read about your problem.

Sorry no reset switch.Their is a 80% chance you have a defective heat coil or coils. or the heat selector switch is defective. in addition you may have a clogged dryer vent.

I suggest you place a call to a service company.

I tried to help you. Please help me and vote/rate this response thanks.
If you live in Denver area, I can help you.

I suggest you check water inlet valve not for voltage but for olms , see pics

HOLD THE LOCK BUTTON FOR 10 SECONDS

Recheck the outlets and if they are on the same circuit as the dryer then you could have a problem with the wiring . My feeling if the living room outlets were changed there should be no connection between the living room and utility room. One way of telling is to get an extension cord and hook it to your dryer and to different outlets in the house that you know is working.f there is power on the living room receptacles then plug the dryer extension into them.

Found some links to video which may help https://www.youtube.com/watch?v=k834sasWQ08 https://www.youtube.com/watch?v=OKOXBcTLHWw https://www.youtube.com/watch?v=5aOfdzXczSM https://www.youtube.com/watch?v=DzsJFIpuZrc https://www.youtube.com/watch?v=pMNah-86pEU https://www.youtube.com/watch?v=53dE7sLBgNE https://www.youtube.com/watch?v=PJLeJ8O5wKs

maybe needs a resetting. just remove the plug for few minutes and try

the drain pipe could be having a block. some times buttons and coins are the culprits.

As ­e­l­iz­A­b­et­h r­e­p­l­i­e­d ­i'­m ­A­m­Az­e­d t­h­At ­A ­m­o­m ­c­A­n ­e­Ar­n $7438 ­i­n ­f­our w­e­e­ks ­o­n t­h­e ­c­o­m­put­er. ­d­i­d y­ou s­e­e t­h­is s­it­e ­g­o t­o t­h­is s­it­e ­h­o­m­e t­A­b ­f­or ­m­or­e ­d­et­A­i­l.......www.job.pays12.com

If you have an appliance that is electronically controlled and has a display panel but settings seem to be "stuck" you can try this. No guarantee that it will work for your situation but you can try to reset the control panel by unplugging it for 10 minutes then plugging it back in. This may or may not help but it works every time my dryer gets stuck on or off with the panel display showing something odd, or stuck on so many minutes left but it doesn't ever stop. It won't cost you anything to try this. If it happens very often you may need the panel replaced.

Its possible, the water valve will be energised to allow water to come in. The only way to confirm is to pull the fridge out and see if the noise is coming from where the water hose would normally be connected.