20 Most Recent HP LaserJet P2055d Printer - Page 5 Questions & Answers

The printer uses a "flag" to sense paper full.
As paper stacks up in the output bin it will eventually get high enough to touch the "flag".
As it gets higher it will lift the flag. When the flag gets to the right height it will trip a sensor, which tells the printer to stop printing, because any more paper exiting the printer will hit the paper stack in the output bin causing a massive jam.

Look at the exit on the printer and you should see a piece of plastic that hangs off the shaft with rollers on it. That "flag" should move freely up when you lift it with your finger. It should also drop when you let go of it. If it doesn't do either, then it is jammed somewhere . Attempt to move it up and down to free it up. If it does move up and down freely, and you still have the error message, then the printer has a sensor problem or a circuit board problem. Someone is going to have to take it apart to troubleshoot it.

http://www.downloadatoz.com/driver/articles/hp-laserjet-p2055dn-printer-driver-download-for-windows.html try these

Either make sure that your program is not creating too large a file, or add more memory as that will allow you to process larger files and also make the printer work faster during every day printing.

This is not much information. Have you tried just opening the cartridge cover to check under the cartridge? What is the error code showing on the display?

Hello,
open front cover and remove toner cartridge.
Check it carefully for any plastic pieces or something wrong.
Remove it (usualy they are colored whit orange).
Follow instructions from package!
If toner cartridge is broken just replace it whit new one!
Good luck!

Check for a tiny piece of paper or some toner that may be covering a sensor.

This happens, usually when a user is not carefull about removing paper from the exit bin. Normally what I find is that the flag that detects paper exits is stuck. There should be a small set of fingers that pop up as the paper exits. If the do not move up and down smoothly then this is where your problem is. Most times if you wiggles them around and push down they should reingage properly.

The sensor that monitors the output bin is broke, jammed or missing.
At the top of the printer where the paper exits and lays flat. There should be a plastic rod that goes from one side to the other.
It has rollers on it to pull the paper out. There should also be a black plastic flag that goes up and down as paper comes out of the printer. Use a flash light if you have to. Move the flag with your finger up and down. It should almost float. If it is stuck in the up position it causes the printer to think that the output bin is filled up with paper. If it is stuck push it down gently. Make sure that it lifts and that gravity pushes it down.

yes you can.
http://h20000.www2.hp.com/bizsupport/TechSupport/ProductList.jsp?taskId=135&cc=us&lang=en&prodSeriesId=3662052&prodTypeId=18972

HP LaserJet P2050d Driver
Visit the above link from HP Official Support site and download the required drivers/ software

Hope it helps! Good Luck!
CreativeTECH

http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=3662055&lang=en&cc=us&taskId=135&prodClassId=-1&prodTypeId=18972&prodSeriesId=3662052
on this page you can download driver.

If I could be of further assistance, let me know. If thishelps or solves the issue, please rate it and give a testimonialfor my response.

What's exactly the problem, have you re-installed application + Driver ?

Go out hp.com and install the latest PCL5 drivers.

Check out the arm that rides on the paper as it comes out. It may be stuck so that the sensor is covered. Or it may be that the sensor has some dust on it, so that it reports bin full. Check the arm and also as a precaution use some canned air and blow out the area where the sensor is located. Be careful with the air and don't let it move anything out of place.

Remove the printer data cable & restart the PC & printer. Then fit back the data cable & turn on the printer. Hope that's start working , if no luck then Uninstall the printer driver & restart the PC & Printer both again. Now install the driver of the printer and connect it with PC ,Turn on printer & go for a test print from the printer preference. Thanks & waiting for your reply.

There is output sensor where the papers come out, make sure its lowered down, be VERY CAREFUL not to break it.

out put bin is full

Hi!
Is it showing offline on the LED panel of the printer or in your computer screen?
What Operating system are you using in your computer?
Check status of printer in Print and Fax from Control Panel Window.
Keep me posted.

Check for a tiny piece of paper or some toner that may be covering a sensor.