Top 20 Epson STYLUS R230 InkJet Photo Printer Questions & Answers

Try this site http://tech.epson.com.au/downloads/category.asp

You need to reset your printer, because the ink counter is full, all you need is to download the Epson Adjustment Program And reset the ink counter back to zero, so you can contineu using your printer

adjust configuration in printer choose between options pdf

All you need is to download the Epson Adjustment Program and reset you ink counter of your printer to zero so your printer back to life

MFG web site? or google.

try a head clean , you will find the head clean program in .. click open the start bar/go to control panel / open devices and printers/ look for your printer ( epson ) and now RIGHT click on your printer and go down to properties/look for the tab "maintenance" run the head cleaner ( you might have to do it a few times )

page setup,the most dpi it can handle or get a photo printer

you can reset it ..also lift top and to the right of the printer you'll see a sponge ..use a syringe to suck the ink out of that sponge .. get this program http://www.ssclg.com/epsone.shtml

take all cartridges out shut off then turn on make surethere is no obstructions where cartridges go replace them one at a time i found a piece of tape on mine would not print black and white removed it now it is fine

Does a nozzle check show anything? Are the inks full and the nozzles clean?

First you could do a printer test. The printer will print a small pattern with all colours making it possible to check if and if so, what nozzle are blocked. Sometimes the cleaning cycle will help, but sometimes there is just some dirt under the head. Please don't try to remove it with tools if there is something. Just use a thick piece or printing paper to solve that problem. Please check the manual for details. Perhaps the epson site can help you with that: http://www.epson.com.sg/sites/epson_singapore/support/support.page

hi , you can see this Epson printer reporting Service Required error

If you will describe the problem, I'll try to help you.

Epson printers have a lock to keep the print heads/carts over on the right side. The lock can get stuck and covered in ink. There is a lever under the edge of the heads that should unlock the carriage so you can get to the "cleaning station" under the heads. Unplug the printer while the heads are moving, and you may be able to move them over and clean. Often the bar the heads run on can be lubricated with light oil, like what you use on a sewing machine, too.

Assuming that you have ink for any color, the problem can either be clogged print-head or an electronic (board) failure no longer controlling a color/colors. The linked procedure may help:

Hi i'm a printer Technician The problem of your printer could be that the surface of the printhead is dirty, and the Cleaning pad/tab doesn't work so good.. Here's a guide i wrote that I done multiple times on my customers printers: 1. Power on the printer, and when the carriage moves from the right to the left side instantly disconnect the power cord. 2. Move the Printer carriage (where the cartridges are installed) on the EXTREME LEFT side, please do it very slowly! 3. Take a syringe of hot water but not boiling, MAX. 70-75 °C 4. Expect the extreme right side of the printhead.. You could be able to see a little squared pad, dirty of ink, and on the left side of that PAD you could see a little rubber strip. 5. Take a tissue of paper and dab the furface of the Cleaner Pad (The squared pad you seen) 6. Take a new tissue of paper and place on it some hot water 7. Without burning your hands try to clean as soon as possible the rubber strip on the right part of the Pad. It would be completely without ink on it 8. Take the hot water syringe and place some hot water on the Cleaner Pad (the amount of water is proportionate to the printer, you have to place water until you see that the surface of the pad is COMPLETELY full of water. 9. Gently move the carriage VERY SLOWLY on the extreme right side of the printer (where there's the Cleaning Pad) 10. Leave the printer like so for 3-5 hours, then restart the printer and do 2-3 cleaning cycles, better with a brand new black cartridge 11. Do a test print (Nozzle Check) and see if there are some changes! Hope the Best!! ADCSFXworks Printing Center

Hi i'm a printer Technician The problem of your printer could be that the surface of the printhead is dirty, and the Cleaning pad/tab doesn't work so good.. Here's a guide i wrote that I done multiple times on my customers printers: 1. Power on the printer, and when the carriage moves from the right to the left side instantly disconnect the power cord. 2. Move the Printer carriage (where the cartridges are installed) on the EXTREME LEFT side, please do it very slowly! 3. Take a syringe of hot water but not boiling, MAX. 70-75 °C 4. Expect the extreme right side of the printhead.. You could be able to see a little squared pad, dirty of ink, and on the left side of that PAD you could see a little rubber strip. 5. Take a tissue of paper and dab the furface of the Cleaner Pad (The squared pad you seen) 6. Take a new tissue of paper and place on it some hot water 7. Without burning your hands try to clean as soon as possible the rubber strip on the right part of the Pad. It would be completely without ink on it 8. Take the hot water syringe and place some hot water on the Cleaner Pad (the amount of water is proportionate to the printer, you have to place water until you see that the surface of the pad is COMPLETELY full of water. 9. Gently move the carriage VERY SLOWLY on the extreme right side of the printer (where there's the Cleaning Pad) 10. Leave the printer like so for 3-5 hours, then restart the printer and do 2-3 cleaning cycles, better with a brand new black cartridge 11. Do a test print (Nozzle Check) and see if there are some changes! Hope the Best!! ADCSFXworks Printing Center <3

Hi i'm a printer Technician The problem of your printer could be that the surface of the printhead is dirty, and the Cleaning pad/tab doesn't work so good.. Here's a guide i wrote that I done multiple times on my customers printers: 1. Power on the printer, and when the carriage moves from the right to the left side instantly disconnect the power cord. 2. Move the Printer carriage (where the cartridges are installed) on the EXTREME LEFT side, please do it very slowly! 3. Take a syringe of hot water but not boiling, MAX. 70-75 °C 4. Expect the extreme right side of the printhead.. You could be able to see a little squared pad, dirty of ink, and on the left side of that PAD you could see a little rubber strip. 5. Take a tissue of paper and dab the furface of the Cleaner Pad (The squared pad you seen) 6. Take a new tissue of paper and place on it some hot water 7. Without burning your hands try to clean as soon as possible the rubber strip on the right part of the Pad. It would be completely without ink on it 8. Take the hot water syringe and place some hot water on the Cleaner Pad (the amount of water is proportionate to the printer, you have to place water until you see that the surface of the pad is COMPLETELY full of water. 9. Gently move the carriage VERY SLOWLY on the extreme right side of the printer (where there's the Cleaning Pad) 10. Leave the printer like so for 3-5 hours, then restart the printer and do 2-3 cleaning cycles, better with a brand new black cartridge 11. Do a test print (Nozzle Check) and see if there are some changes! Hope the Best!! ADCSFXworks Printing Center

The cartridge head may have gotten clogged. Take the cartridge out and clean the head with a damp cloth and print a couple of pages to set this right. Also, print a test page to make sure the ink hasn't dried up. If it has, you will have to get a new cartridge.

have you seen any dirty white foregin item inside the printer,you can also see CR motor upper side of ink westpad.