Sony Walkman NWZ-B135 MP3 Player - Answered Questions & Fixed issues

Sony walkman b135 say boot error after that power

Check the Sony site. If it is available or needed they would have the driver. Also best place to ask about if it works with that op system.

sounds like it is playing in random mode. you may be able to change in 'settings.'if not, maybe the files are out of order...depending on how they are named, it could be causing issues.

hi my ipod is full charging but not turn on

Format it completely

it might be serious check out with the service centre ........

Depending in its age, the battery might just be shot. It may say full charge cause it takes all it can but it might only be a few min worth. Most Mp3 players can be taken apart and the battery replaced.

what will i do?

I think you are having the same problem I had.

I found that if the Bass was turned on then you couldn't access the equalizer.

Once I had turned it off, no probs. To turn it off simply press the bass button on the top of the player.

Hope this helps.

Okay?

Hi allison mccl...

If you ever find that you have to deal with a wet device, don't just abandon it.
Instead, try the following method to repair the water damage:
DO NOT TURN IT ON!
Take it apart as much as you can. Take out the battery, the memory card and whatever else can be easily disassembled. (Just make sure you can put it back together.)
Store the parts in an air-tight container covered with either dry rice, silica gel packets or kitty litter. These will absorb the moisture from your electronics device, leaving it water-free.
If no rice, gel packets or kitty litter are available, try using a vacuum to **** the water out.
DO NOT blow-dry the parts, it will only force the water farther in and cause more damage.
Please take time to rate me.

its the problem with your headphone jack. check with other headsets otherwise female jack problem in your player

Hi,

I'm sorry to know that the Walkman player is not getting charged. I'll be glad to assist you with this. Please perform the following steps:
If the New Hardware Wizard appears and is prompting for a location of the driver, point to the following directory: C:/WINDOWS/INF .
To function properly, your Walkman player must be recognized by your computer as a Media Transfer Protocol (MTP) device. If the portable player was connected to the computer before the Windows Media Player version 10 or later was installed, it will be recognized as a Mass Storage Class (MSC) device and not function properly. In that case, a different procedure is available to correct this issue.
For some models, when you use the portable player for the first time, if you have not used it for a long time, or the battery is depleted, it may take up to 5 minutes for it to be recognized or start charging. On models with a display, the display will remain blank. If it the portable player is not recognized or does not begin to charge after waiting 5 minutes, reset the player by pressing the reset button.
If this is not the first time using your player and it was working properly at one time with no major changes performed (such as restoring the operating system or replacing a hard drive), follow the procedure below:
Connect the portable player to the computer using the supplied USB cable.
Disconnect the USB cable from the portable player and then reconnect.
Check the connection status again.
Disconnect the USB cable from the computer and then reconnect.
Check the connection status again.
Check for available space on the player using Windows Media Player or My Computer .
Restart the computer.
Check the connection status again.
Check that the USB cable is firmly connected to both the computer and the player.
Check the connection status again.
If the player is connected to a USB hub, disconnect it and connect it directly to the computer with a dedicated USB cable.
Check the connection status again.
If the player is still not recognized by the computer, disconnect all devices connected to the computer with a USB connection and restart the computer.
After the computer restarts, connect only the Walkman player and test the connection again.
If the player is still not recognized by the computer, try a different USB port.
Check the connection status again.
Under the Common settings menu of the player, format the player using the built-in Format utility.
Check the connection status again.
Verify the current Operating System. If it is an upgraded operating system, contact the computer manufacturer for updated drivers for their upgraded operating system.
If you are running the Windows XP operating system, be sure you are running Service Pack 2 (SP2) or later.
If you did not have the latest service pack, test the connection status again after it has been installed.
If you are still unable to transfer music to your player and have not yet uninstalled and reinstalled the driver follow the procedure to confirm that the player is recognized by the computer as an MTP device.

Thanks for contacting FixYa.

What I did was drain the battery completely then try again. Worked for me.

cool

my sony nwz-b142f voulme button is not working. I've try to do but its voulme only decreases not increases..?? what to do..?? please help.!

Hi there.... You can try other computer if they can detect the Sony Walkman that you have, if not being detected, have the device physically check.... if being detected by other computer, try updating the driver or software for that Sony device..
Thank For Using Fixya

If your PC has windows xp sp2 or later and Windows Media Player 11and f you have problem with your device follow this steps:
1. Connect the player to the computer.
2. From the computer, select start - Control Panel - Performance and Maintenance - System. "System Properties" is displayed.
3. Select Hardware tab, and open Device manager.
4. Open Universal Serial Bus controllers, and select USB Mass Storage Device or WALKMAN NWZ-XXXXX.
5. Select Action - Update Driver ... from the menu bar. "Welcome to the Hardware Update Wizard" is displayed.
6. A dialog on Windows Update connection will be displayed. Select No, not this time., followed by Next.
7. Select Install from a list or specific location [Advanced], followed by Next for the hardware install method.
8. Select Don't search. I will choose the driver to install., followed by Next for the search and install option.
9. Check Show compatible hardware, and then select MTP Device* in the model list, followed by Next. The device driver is installed.
10. "Completing the Hardware Update Wizard" message is displayed, and confirm "MTP Device" message. Click Finish.

This advice can help if your player can work correctly.
Thanks.
gylacz

Hi Chilysg,

Please find the manual on this link http://bit.ly/iJZr6h

Make sure that you save this manual to your computer so that you can use it in the future.

Hope it helps ..:)

just hit the reset