Jura Capresso Impressa X7 Espresso Machine - Answered Questions & Fixed issues


Have you descaled it regularly? Do you have hard water?
Sounds like it's clogged with scale. Try running white vinegar and water through, see if that unclogs it.

Jura Capresso... | Answered on Jun 03, 2019 | 41 views


Hi, a video how to fix your Jura step by step, good luck... http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

Jura Capresso... | Answered on Mar 23, 2015 | 241 views


kitchen.manualsonline.com

Jura Capresso... | Answered on Sep 15, 2014 | 525 views


remove tank clean with hot water, rinse and shake you should hear a rattle in the bottom of the tank. if you dont the the small black float built into the tank side wall is stuck. once free it will work fine.

Jura Capresso... | Answered on Mar 04, 2014 | 139 views


small black rectangular float is stuck in the water tanks . take off tank and empty. then shake you will see it on the side wall (machine side) if it does not rise when water is filled the machine still thinks its empty

Jura Capresso... | Answered on Jun 28, 2016 | 523 views


Either there is issue with the Sensor or the Thermoblock. you'll have to replace either of these.

Jura Capresso... | Answered on May 20, 2019 | 1,172 views


The milk tubes should be submersed into water with a milk cleaning agent. sounds like you've left the milk tubes drawing from the fridge with milk in it.
Bean to cup cleaning

Jura Capresso... | Answered on Sep 29, 2013 | 243 views


I would like to know more in order to better understand. When any of the steam functions are selected do any errors display? Also, does steam come up through the machine from inside? It could also be that a solenoid valve (electronic valve that can operate flow) may be bad. It almost sounds like the problem you have may be coincidental with the hose incident and now it's a little harder to diagnose.

Jura Capresso... | Answered on Dec 23, 2012 | 392 views


Hi Error 4 is the following fault :STEAM: Temperature sensor notify “value above tolerance” I think only a trained engineer could fix this unfortunately. Hope it helps though. Alison

Jura Capresso... | Answered on Apr 01, 2018 | 2,606 views


malfunction 4 is the steam boiler sensor has failed

Jura Capresso... | Answered on Sep 16, 2011 | 487 views


Try the following link we are sure they will be more than happy to help you find what you are looking for
http://www.partsguru.com/JuraEspresso.html

Jura Capresso... | Answered on Jan 30, 2016 | 408 views


see if this helps you. the answer should be in section 14. http://jura-impressa.cz/files/files/35file.pdf
if you need additional help please let me know.

Jura Capresso... | Answered on May 04, 2011 | 2,447 views


There is a little shoot that you pull up between the grinders, the pills fit there, if they do not they are the wrong pills. they should be semi circle pills

Jura Capresso... | Answered on Feb 13, 2010 | 174 views


It runs until the water runs out so if your water tank is full it will run a very long time. Use only the amount of water specified in the manual.

Jura Capresso... | Answered on Aug 26, 2009 | 128 views


add a capfull of the cleaning fluid to a litre of water, insert milk tube and request cappuccino clean from the cleaning button...icon of cleaning tablet surrounded by water droplets, second row second button from lefthand side...then follow screen instructions to step your way through the cleaning selections with +and - buttons.
I keep the cleaning fluid held high to allow it to continue running after the cleaning action.
Remember to run clean water through the pipes using the same method above.

Google x7 manual and you can download one of many copies online.

Jura Capresso... | Answered on May 19, 2009 | 613 views


Two to three teaspoonful water overflow after each espresso is normal. That is why the tray is there.

If water collection in the tray is excessive and programmed espresso is smaller, then there is cause for worry.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Jura Capresso... | Answered on Oct 23, 2016 | 256 views


Error 5 is pointing to heating problem. Here are the parts that may be malfunctioning:
1- Thermal sensor not registering heating. Replace it.
2- Heater not heating up. Check continuity on heating element. If there is no continuity, (This is rare). Replace heater (Thermo block).
The problem can be linked to:
1- Missed descaling of machine for extended period.
2- Use of automatic descaling method suggested by Jura. Descale the machine every three months using Manual descaling method.. Services Unlimited Inc Parts Guru Since 1988

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Jura Capresso... | Answered on Oct 23, 2016 | 132 views


Fortunately the problem you describe is not model specific. All Jura machines in the series C, E, F, J, S & Z models have the same problem. The Jura recommended maintenance is insufficient or erroneous. Here is how it occurs:
1- When new machine is set up, the instructions advice the owner to set up OK for use of Filter cartridges. This set helps only to display reminders for replacing the filter.
2- The initial set up instruction also advises that with regular use of Filter, descaling the machine will not be needed. That is really not accurate. Consequently, the reminders for descaling are delayed for over one year or more. This causes serious consequence with accumulation of Calcium deposits in the entire hydraulic and coffee system.
3- Use of Filters alone does not prevent Calcium deposits. Cleaning tables recommended & sold by Jura do not remove Calcium deposits in the coffee/water passages. The automatic descaling method recommended by Jura leaves the coffee side of the machine unclean. The error message in your machine is due to Calcium deposits in the Brew group, coffee outlet & the faucet dispensing coffee in the cup. I suggest all Jura machine owners should manually descale machine. Manually descaling includes use of 6 to 10 rinse cycles with descaling solution in the water tank. The error message "Clean Machine" is accurate. This error message is pointing to descale the Brew group, coffee outlet tube and coffee dispensing faucet by using rinse cycles.

After the rinse cycles are complete, refill Descaling solution in the water tank & continue descaling the rest of the machine by using hot water dispensing function, ½ cup at a time until the tank is empty. Finally, give a final flushing of machine to flush out remaining descaling solution inside the machine.
Services Unlimited Inc Parts Guru Since 1988

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Jura Capresso... | Answered on Oct 23, 2016 | 294 views


Hi Shoba
Photo sensor or switch is blocked.
Not sure if yours is an Infra Red beam or switch
Clean & inspect with flashlight
Look for light path (blocked) or moveable part (switch)

Actually.... it must use an Infrared Light Emmiter to shine through the grounds holder to the sensor on the other side/

10 Minute Fix.... I hope

Jura Capresso... | Answered on Jun 16, 2015 | 742 views


Plug it in.............................

Jura Capresso... | Answered on Oct 28, 2014 | 73 views

Not finding what you are looking for?
Jura Capresso Impressa X7 Espresso Machine Logo

48 questions posted

Ask a Question

Usually answered in minutes!

Top Jura Capresso Coffee Makers & Espresso Machines Experts

The Knight
The Knight

Level 3 Expert

76140 Answers

markybean

Level 1 Expert

40 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Jura Capresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...