Jura Capresso C3000 Espresso & Coffee Maker - Answered Questions & Fixed issues


Hi all, I have the exactly same problem on my Gaggenau CM470 however the drip tray is clean and the contacts in the back is also 100% clean.. I wonder if its possible to disable the sensor/switch on a CM470 ?

img_0058-e0ag3skiwqxij25yukiuvad0-5-0.jpeg

img_0061-e0ag3skiwqxij25yukiuvad0-5-2.jpeg

Jura Capresso... | Answered on Nov 23, 2018 | 1,947 views


I had one that set for 6 months that had that problem. Air had gotten into the water lines. Opened the hot water tap a few times and then removed the end of the water line that runs from the solenoid to heater block to at the solenoid end to bleed air out. It could also have been some calcium deposits that blew out with the air blocking the line. Then I replaced the end of the line, powered the machine up and it worked normally. Note: Jura Capresso and Capresso machines are complicated and it takes some mechanical know how to open them up and service them. They also have four special screws on the back that requires a special tool to open

Jura Capresso... | Answered on Dec 24, 2013 | 1,144 views


Cleaning instructions for that machine can be found in the user guide at the link below:

http://www.capresso.com/pdf/super_c3000.pdf

Jura Capresso... | Answered on Nov 20, 2013 | 65 views


User guide found at the below link has cleaning instructions:

http://www.capresso.com/pdf/super_c3000.pdf

Jura Capresso... | Answered on Nov 20, 2013 | 148 views


It could be a setting that casues this instant brew function that accidently got set. Look at the user manual?

Jura Capresso... | Answered on Oct 28, 2013 | 45 views


I found out where it goes, thanks to Juergen, who pointed me toward his excellent page on Jura cleaning: see figure 7d, copied here
2_4_2013_4_19_54_pm.jpg
which shows the yellow clip helping to hold on the tea pipe. I'm guessing that if you don't use the tea pipe, you will be okay. Otherwise you can just put that clip back on next time you clean the machine.

Jura Capresso... | Answered on Feb 04, 2013 | 339 views


You need to go into program mode, which is done by either pressing the "P" button or pressing and holding the circular dial until it says filter with a tick or minus. Then you tick or untick it, or both and it will ask you to install the filter.

Depending on the model you may need a filter extender that plugs on to the top of the filter then you install the filter into the holder that is just below the circular monthly reminder that is in the tank.


There is a document for the F50 here: http://www.quaffee.co.za/Pages/guides/ImpressaF50_QuickRefMaintGuide.pdf

Jura Capresso... | Answered on Sep 09, 2012 | 71 views


Yes
You should run the decalcify program with the JURA decal tablets or DURGOL. Do not use other agents.
See page 25 of user manual.

---


Please dont forget to vote this answer was helpful

Many thanks

------



Jura Capresso... | Answered on Feb 14, 2011 | 300 views


I have the same problem for the second time, it's the damn switch at the end of tray slot, but it's unaccessible, either from the front or from the back of machine. It appears that casues a program error and the controler unit. First time I end up paying the $250 flat fee to repair it.
My machine is 7 years old, and it's been good so far, but I'm not in the mood to pay another $250.

Jura Capresso... | Answered on Mar 27, 2010 | 211 views


No, your damn right, theres no tool on the market for tohse screws.
I did it with a fine end point pliers, it cause litle damage to the screws head, but worked.

Jura Capresso... | Answered on Sep 10, 2010 | 566 views


I have a Capresso fo 7 years now, had few problems, but always solve them.
If youe machine does all the functions properly, but doesn't give you coffee, you should check if everytnhig goes into the grounds tray. If that's the case you may only have a broken "O ring" inside the pressing element. It makes the coffe, but throws it away instead of filling the cup. I had that problem, and it was the "O ring".
If the grounds dunped on the tray are dry, you're looosing the water in the back, probably on the relief valve.
Hope this helps!

Jura Capresso... | Answered on Jan 21, 2014 | 1,139 views


We had the same problem. We unplugged the unit from the wall and then plugged it back in again. For us, it was as simple as that.

Jura Capresso... | Answered on Oct 16, 2009 | 254 views


There are to oval screws on the backpanel. After removing the panel, unscrew the powerboard and check the flowmeter behind it

Jura Capresso... | Answered on Oct 06, 2009 | 708 views


The first thing to check is the seating of your water tank. Just a few grains of coffee grounds or dirt underneath the tank are enough to break the watertight seal. Make sure the area under the tank is absolutely clean.

That's always worked for me when I've had the leaking problem.

Jura Capresso... | Answered on Sep 02, 2017 | 268 views


Request the wiring diagram directly from Jura.

Jura Capresso... | Answered on Jan 28, 2017 | 149 views


Rinsing cycle at start up is electronically programmed function. Unplugging is a temporary solution.
Jura will not sell parts or offer any guidance.
I could look into more details to find an answer but the model Capressa 50 is not listed in my Data base.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Jura Capresso... | Answered on Dec 30, 2016 | 41 views

Not finding what you are looking for?
Jura Capresso C3000 Espresso & Coffee Maker Logo

45 questions posted

Ask a Question

Usually answered in minutes!

Top Jura Capresso Coffee Makers & Espresso Machines Experts

The Knight
The Knight

Level 3 Expert

76054 Answers

markybean

Level 1 Expert

40 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Jura Capresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...