Jura Capresso Ultima 121 Espresso Machine - Answered Questions & Fixed issues

Hi M Ward, I have the exact same problem. Did you find a solution for this part being stuck and not cleaning the old ground coffee?

Call Capresso. They'll send you a new gasket for free.

It sounds like a gear mech is stuck, or stripped, or not working. I'm not familiar with these machines, but if a gear is just jammed, sometimes you can try to assist the movement and free it up (if you can get to the carousel). You'll have to take the unit apart to see what's going on, otherwise.
You might be able to get some support from Jura, so contact them:
http://www.jura.com/home_x/service_support.htm
Good luck, and hope this helps.

You can order a new carousel from Capresso. It's $90, though:

http://www.capresso.com/pdf/order-ultima.pdf

Make sure the lever is up when turning the carousel, and keep the button at the back of the machine depressed while screwing the carousel onto the unit (and while taking it off the unit). I think the positioning of the button point at the beginning of the carousel replacement process is also important:

http://capresso.com/pdf/inst_esp_ultima.pdf

try this sight
www.saecoparts.com/SaecoEspressoClassicoBodyparts.html - 70k -

Capresso told me the only way to buy it is the $90 entire top assembly.

I have the exact same tube that fell out of mine. Does your still work? I assume it has something to do with baffling the air intake for the frothing area.

Unfortunately, without being there in person to inspect the machine and its components, it's difficult for me to provide a definitive answer. However, I can offer some general guidance that may help:

1. Consult the user manual: The user manual for your Capresso C3000 should have a diagram or schematic showing the different components and their connections. If you still have the manual, check to see if there's a helpful diagram inside.
2. Look for visual cues: While it can be difficult to identify the tubes by sight alone, there may be visual cues that can help you narrow down which tubes go where. For example, one tube may be thicker or more flexible than the others, or it may have a different color or texture.
3. Experiment with different configurations: If you're unable to find a diagram or visual cues, you may need to experiment with different configurations until you find the correct one. This can be time-consuming and frustrating, but it may be the only option if you're unable to find any other information.
4. Seek professional help: If you're still unable to identify the correct tube configuration, you may want to consider seeking professional help. A qualified technician or repair service may be able to identify the correct configuration and get your machine back up and running.

I hope this helps, and I wish you the best of luck in getting your Capresso C3000 back in working order!

http://www.fixya.com/support/t12615678-capresso_303_will_not_steam

Talk him

The first thing to check is the seating of your water tank. Just a few grains of coffee grounds or dirt underneath the tank are enough to break the watertight seal. Make sure the area under the tank is absolutely clean. That's always worked for me when I've had the leaking problem.

Rinsing cycle at start up is electronically programmed function. Unplugging is a temporary solution. Jura will not sell parts or offer any guidance. I could look into more details to find an answer but the model Capressa 50 is not listed in my Data base. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

TRY SWITCHING IT OFF AND RETRY LATER MAY BE IT WILL RESET IF NOT CHECK FOR ERROR OR TELL US MORE ABOUT THE FOULT

You really don't give which machine - but here is link to company product support. Maybe they will have product manual to help trouble shoot issue. Sorry could not of been more help Product Support

The switch or photo sensor is not sensing any beans present. So it can't continue Use torch to inspect bean entry area Small brush etc

Hi Marton Registered repairers love you guys.... If you carry a smartphone these days and most of us do. You need to learn to take photo's first. Even the Las Vegas pro restoration guy on TV does that. Sorry I don't have those photos and you'll be really lucky is someone on Fixya does. Try YouTube videos.

What model do you have? What's the problem you are trying to fix by resetting it?

Just a guess here but if you are not using soft water you may have a hard water scale coating on the sensor. The sensor is preventing the heating element from powering up because it thinks there is no water. Try filling the machine with vinegar for several hours (no more than overnight) This will dissolve hard water deposits and hopefully clear the sensor. (the sensor should be a simple continuity contact. If you can look inside and see a metal button and it is fouled clean it off.)

Try running distilled white vinegar through it.

constant heating message on screen is from a thermal fuse blown on one of the boilers. service call required i'm afraid...... very cheap part about 10 euro