Replacement Parts for Fitness Exercise Equipment at SPORTSMITH
You have posted this question in the Stair Climber section, but the error you are listing is a treadmill error code. The following information should help.
Probable Cause
A) Incline control error.
B) Insufficient power source.
C) User exceeds weight limit.
D) Unit will not lift.
E) Unit thinks it is always at 0% incline and only lifts up.
F) 3 amp circuit breaker has tripped.
G) CPU board has stuck relay.
H) Lift motor is faulty.
Corrective Action
A) Access the incline manual mode in diagnostics by pressing 9, 1, 9, ENTER and then pressing HILL program key. Incline the unit with two people on the unit. B) Ensure treadmill is connected to a dedicated 120V, 20 Amp circuit.
C) Advise user of unit's weight limit of 300lbs (137kg).
D) Perform the lift test procedure by pressing 9, 1, 9, ENTER and then pressing HILL program key.
E) Inspect the home switch for smooth operation and inspect the wiring of the home switch for damage or poor connections. Inspect the lift motor cable connections and for the presence of the suppressor board (should only be 1).
F) Test the circuit breakers and replace if necessary.
G) Replace the CPU board.
H) Replace the lift motor.
LifeFitness 9500 Treadmill Lift Control Error
Please Help,I have just bought a used treadmill life fitness T3, and i have jut put it on but in the top its saying Replace the emergency stop switch, i don't know what it means as this is the first time i bought one :(
This sounds like a motor control board issue. In my experience I have seen it either speed up when it is supposed to slow down or you will get a pulsating or lunging type action in the running belt. There are companies available that can test and repair said board for a fraction of the price. You might check with Carolina Technical Services LifeFitness motor controller repair
This indicatin is problem with the speed sensor, see the diagram attached, test the s. sensor for open or faulty. clean it, and tigh the plug or connector very well.Try to run The software calibration for easy diagnose,troubleshooting, and fix it. God bless you
RUN the software calibration for diagnostic, troubleshooting and fix it.2) LUBE THE deck belt3) LUBE the rollers bearing4) adjust the speed sensor see the diagram, clean it, and tight the plug 5) adjust the REED swtich see the diagram, clean it, and tight the plug.6) see the block d. God bless you
adjust the speed sensor , see the diagram, clean it , and tight the plug or connector very well, and test it and replace if necessary2) measure the input voltage for motor, if there are the motor need repair, see my personal TIPS3) test the output voltage board, for input voltage motor, if there are NOT the board is faulty, see the b. diagram attached..God bless you
LUBE the deck belt,this happens because the lack of maintenance2) LUBE the rollers bearing too, very important.3) adjust the speed sensor see the diagram attached, clean it, and tight the plug.4) adjus the REED swtich, see the diagram clean it, and plug the connect very well.5) Try after you did the adjustment RUN the software calibration for diagnostic, troubleshooting, and fix it. God bless you
1) lube the deck belt2) lube the rollers bearings3) measure the input voltage motor, if there are the motor need repair4) measure the output voltage board, for input voltage motor, if there are NOT the board is faulty.SEE The block.God bless you
Typically a non start up of any electrical Exercise equipment raises alot of red flags If this treadmill will not start Check the internal fuse MAKE SURE ITS NOT PLUGGED IN!!!! UNPLUG IT FROM THE WALL2 If there is NO Fuse and you just bought it new Return it for an exchange.3 Check your wall outlet for less then 5 Bucks you can buy a wall outlet tester that tells you if your Outlet is good Or Bad.4 DO NOT Attempt to service this item on your own the way they make treadmills you have to have a qualified service tech come out and fix it because the risk of serious shock or death is emminent.
Dear Sir:Please do it with a pencil under the display board. There is a small orifice, and with the point of pencill tocuh and then turn on the machine. sincerely. God bless you.ernesto cuadramanagua, nicaragua. c.a
the best way is read you instruction manual, for instruction about this notification.2) You must Lube the deck belt, by lack of maintenance you can have this notification. 3) Lube the rollers bearing.4) Download the instruction manual if you do not have www. fitness.manualsonline.com or www. iconservice.com5) Run the software calibration for diagnose and troubleshooting.God bless you