Yukon Wolverine Multi Station Gym - Page 9 - Answered Questions & Fixed issues
Pacemaster Pro Elite error code 35
Error code 35 on a Pacemaster Pro Elite treadmill typically indicates a problem with the treadmill's speed sensor. This sensor is responsible for detecting the speed at which the treadmill belt is moving and providing that information to the treadmill's control panel. If the speed sensor is not functioning properly, the treadmill may display error code 35 and stop operating.
There are a few things you can try to troubleshoot and fix this error:
- Check the connections between the speed sensor and the control panel. Make sure that the connectors are securely plugged in and that there are no visible signs of damage.
- Clean the speed sensor. The speed sensor may be dirty or covered in debris, which can affect its ability to accurately detect the treadmill's speed. Use a dry cloth to gently wipe away any dirt or debris.
- Check the treadmill belt for proper tension. If the belt is too loose, it may cause the speed sensor to malfunction. Adjust the belt tension according to the manufacturer's instructions.
- Replace the speed sensor. If none of the above steps fix the problem, the speed sensor may be faulty and need to be replaced. This is a more complex repair that may require the assistance of a professional.
I hope these suggestions help you resolve the error code 35 issue on your Pacemaster Pro Elite treadmill. If you are unable to fix the problem or if the error persists, it is recommended to contact the manufacturer for further assistance.
12/25/2022 9:29:24 AM •
Exercise &...
•
Answered
on Dec 25, 2022
•
115 views
My 2 years old Reebok one gt40s keeps on suddenly stopping after only few minutes walking on. Could anyone help me what to do?
There could be a few possible reasons why your Reebok One GT40s treadmill is stopping suddenly after only a few minutes of use. Here are a few things you can try:
- Check the power cord and outlet. Make sure that the power cord is securely plugged into the treadmill and the outlet, and that the outlet is functioning properly.
- Check the treadmill's safety key. The safety key is a small device that helps to prevent accidents by shutting off the treadmill if it becomes disconnected from the control panel. Make sure that the safety key is properly inserted into the treadmill and the control panel, and that it is not damaged or loose.
- Check the belt and deck. If the belt is slipping or the deck is not properly lubricated, it can cause the treadmill to stop suddenly. Make sure that the belt is properly aligned and tightened, and that the deck is adequately lubricated according to the manufacturer's recommendations.
- Check for any visible damage or loose parts. If you notice any visible damage to the treadmill or any parts that are loose or not functioning properly, it may be necessary to have the treadmill serviced by a professional.
I hope this information is helpful. If the problem persists after trying these steps, it is recommended to have the treadmill serviced by a professional to ensure that it is functioning safely and correctly.
12/22/2022 11:15:16 PM •
Exercise &...
•
Answered
on Dec 22, 2022
•
337 views
Hello! , having problems with my treadmill. When the key is inserted, all lights go on and the incline works fine, but when you press start to start walking, the belt does not move and display E2.
Error code E2 on a treadmill typically indicates a problem with the speed sensor. The speed sensor is a small device that measures the speed of the treadmill belt and sends a signal to the treadmill's control panel. If the sensor is not functioning properly, it can cause the treadmill to display an E2 error and prevent the belt from moving.
There are a few potential causes of an E2 error on a treadmill:
- The speed sensor may be loose or misaligned. Make sure that the sensor is securely attached to the treadmill frame and properly aligned with the magnet on the flywheel.
- The speed sensor wire may be damaged. Check the wire for any visible damage, such as fraying or cuts.
- The control panel may be malfunctioning. If the error persists even after checking the sensor and wire, the control panel itself may be the issue. In this case, it may be necessary to have the treadmill serviced by a professional.
I hope this information is helpful. If you continue to experience problems with your treadmill, it is recommended to have it serviced by a professional to ensure that it is functioning safely and correctly.
12/22/2022 11:12:17 PM •
Exercise &...
•
Answered
on Dec 22, 2022
•
849 views
Keys 8800 Treadmill Won't Incline
If your Keys 8800 treadmill is not inclining even though the incline motor is running, it is possible that the worm drive shaft has become damaged or has become disconnected from the motor. This is a mechanical issue that will need to be addressed by a trained technician. I recommend contacting Keys Fitness or a qualified treadmill repair service to have the problem diagnosed and repaired. It is important to have this issue resolved, as using a treadmill with a damaged or malfunctioning incline mechanism can be dangerous.
12/10/2022 4:56:44 PM •
Exercise &...
•
Answered
on Dec 10, 2022
•
51 views
What does error 11 mean and how to fix error 11
Hi,
it could be that there is too much friction between the belt and the portion of the machine below it. Try squirting some oil below the belt and let it run for a little bit before hopping on the treadmill again. Otherwise, you might need to have the treadmill serviced through it's manufacturer.
Thank you.
12/3/2022 4:01:44 AM •
Exercise &...
•
Answered
on Dec 03, 2022
•
41 views
How do I reboot my technogym want run
Hi,
usually you have a power button on the machine that you can press once to shutdown and once again to power up. It looks like a circle with a vertical line intersecting the top. So you can press that twice with a 15 second pause in-between presses.
Thank you.
11/17/2022 1:29:38 AM •
Exercise &...
•
Answered
on Nov 17, 2022
•
117 views
Not finding what you are looking for?