20 Most Recent Kenmore 63822 / 63824 Bottom Freezer Refrigerator - Page 5 Questions & Answers

There is a communication issue with the display board and the main unit.

You may have a problem with the gear assembly for the freezer tray on your Kenmore Elite refrigerator. The gear assembly is responsible for supporting the rear of the basket and keeping it in place. Your description sounds like your gear assembly may be an older generation and may not have screw holes for attaching the gears to the support arm sliders. The gears may be designed to be snapped into place on the support arm sliders. The plastic tab you mentioned at the back of the slider is likely the attachment point for the swivel hub on the gear. To attach the gears, align the swivel hub with the plastic tab, then gently push it in until it snaps into place. The tab may be jammed or stuck; in that case, you can gently pry it loose with a small flat-head screwdriver. If you continue to have trouble installing the gear assembly, consider contacting Kenmore's customer service for further assistance. They can provide you with a detailed exploded parts diagram or even a video tutorial on installing the gear assembly properly

20.7 cu ft.

What Are Some Specifications of the Kenmore Coldspot ...

https://www.reference.com > World View The Kenmore Coldspot 106 is a 20.7-cubic foot side-by-side refrigerator with a reverse osmosis Pur water filter, ice maker and digital controls.

If your appliance is displaying an error code that flashes "H" and "F" repeatedly, it may indicate a problem with the temperature or humidity in the appliance. This could be caused by a malfunctioning sensor or a problem with the control board. To troubleshoot the issue, you can try the following:

1. Check the door seals to ensure that they are clean and in good condition.
2. Make sure that the appliance is level and that there is sufficient ventilation.
3. Check the temperature and humidity settings to ensure that they are set correctly.
4. If the problem persists, it is best to have the appliance checked by a professional. They will be able to diagnose the problem and suggest the appropriate repairs.

It is important to note that this is just a general guide and the specific cause of the error code may vary depending on the make and model of your appliance. Be sure to refer to the user manual or contact the manufacturer for specific troubleshooting steps.

If the control panel on your Kenmore dehumidifier is flickering on and off, there could be a few potential causes for this issue:

1. A loose or damaged control panel display ribbon cable. This cable connects the control panel to the main circuit board and any damage or looseness could cause the control panel to malfunction.
2. A faulty control panel display. If the control panel display is not functioning properly, it could cause the control panel to flicker or not work at all.
3. A faulty main circuit board. The main circuit board is responsible for controlling the various functions of the dehumidifier, and any issues with it could cause problems with the control panel.

To troubleshoot this issue, you may want to try the following:

1. Check the control panel display ribbon cable for any visible damage or looseness.
2. If the cable appears to be in good condition, try resetting the dehumidifier by unplugging it and then plugging it back in.
3. If the issue persists, you may need to contact a professional for further assistance in diagnosing and repairing the issue with your dehumidifier.

This is most likely due to the defrost thermometer. However, proper testing is recommended by a technician to be sure. It is located at the back of the inside freezer cabinet. You will have to remove the shelves and drawers to access a panel secured with hex screws. When the panel is off, the small round silver piece with a red and black wire is the defrost thermometer. Be careful of the fins around the coils as they are extremely sharp.

F01 is a general error code that indicates a problem with the electronic control board. The clicking sound you are hearing may be the result of a failed component on the control board. It is possible that the control board may need to be replaced. However, it is also possible that the issue could be with another component in the dryer, such as a faulty relay or a damaged wire connection. To troubleshoot the problem, I would recommend checking all of the wire connections to ensure that they are secure. You should also check the relay and make sure that it is functioning properly. If the issue persists, you may need to consider replacing the electronic control board. If you are not comfortable working on the dryer yourself, I would recommend contacting a professional appliance repair service. They will have the tools and expertise needed to diagnose and repair the problem.

https://removeandreplace.com/2015/05/27/freezer-drain-frozen-water-dripping-into-refrigerator-how-to-fix/

Sears is the best place for parts and they also have diagrams. https://www.google.com/search?q=Kenmore+side+by+side+Refrigerator+Model+795.5103+parts& ..

This is a 20 cubic ft. side by side refrigerator.

Yes you do. If any of the wires touch the casing it will fuse and if you get electrocuted you will FOR SURE drops the wires!

25 cu ft

Kenmore Refrigerator Size By Model Number! 2022

https://homeguideinfo.com > kenmore-refrigerator-size-... Nov 2, 2022 - The Kenmore refrigerator model 596 is a refrigerator model that spans around 25 cubic feet. This design of the Kenmore has a French door with a ... ‎Where Can I Find the Cubic... · ‎What Size is Kenmore... · ‎How Many Cubic Feet is...

The Kenmore 795.73053 refrigerator is made by LG. The F dH code indicates that the defrost cycle took over 80 minutes or the defrost temperature sensor did not report a temperature over 46.4 degrees (F). This could be caused a failed or disconnected temperature defrost fuse, a problem with the defrost heater or a blockage of the defrost drain. If the drain opening is clogged by ice, pour warm water over the drain line until the opening is completely clear. The defrost heater could have the electrical wiring come loose. In that case, just replacing the wiring harness will solve the problem. Similarly, if the fuse is intact, try securing the connector so it doesn't come loose. If the fuse has failed replace it. If the fuse is good and no wiring is loose, replace the heater. Note: check the full model number of the refrigerator. The parts diagram for the 795.73053411 is here: https://www.searspartsdirect.com/model/3ubdo9sqjd-000582/kenmore-79573053411-bottom-mount-refrigerator-parts . The all parts list has the defrost heater. If you unplug the refrigerator for at least 30 seconds, the error code will be reset. Otherwise, the error will disappear after the system correctly defrosts. I hope this helps. Cindy Wells

20.7 cubic feet. Didn't I answer this already??

What Are Some Specifications of the Kenmore Coldspot ...

https://www.reference.com > World View The Kenmore Coldspot 106 is a 20.7-cubic foot side-by-side refrigerator with a reverse osmosis Pur water filter, ice maker and digital controls.

Your water dispensing valve has gone bad. I don't have your model # but here's the most common location there's a valve in the very bottom (back) of the fridge... It's basically what the water line screws into. This is the valve that controls flow that's gone bad. You can head over to Repairclinic.com or appliancepartspro.com and purchase one, it's not a major job. Always be sure to unplug the unit before servicing. You'll need the Model # too. The sites shows where it's most likely located. Best to you!

Hi, I'm seeing that it's 25.6 cubic feet on the Home Depot website. For further details, please search for the fridge on that website or reference the product manual of the fridge. The table of contents should allow you to find the specific page with fridge dimensions if not on the Home Depot website. Thank you.

I've used used a compressor for that drain hole at the back of the fridge. A hanger wire will work too. I've never tried it but maybe a can of compressed air might work also.
The water drain line is plugged and that little catch tray is overflowing. That's why you're ending up with water under your bins inside the fridge. The problem is not in the freezer or else you'd have a skating rink on the floor of the freezer.
I don't recognize the photos exactly but they're all the same principle. Take everything out of the fridge , including the racks. It's far easier than o find the screws and disassemble the drain "catchall".
Good luck.

It seems to be because it is a Canadian model! Where I am :>) You can probably order parts on the '970' model number alone. Most sites will give you a schematic. https://www.google.com/search?q=Kenmore+970-254324 ..

Hi, Please look for any arrows directing the connecting of the two on the back of either one of the elements. If you cannot find this, the we'll have to move onto using any construction instructions within the manual of your kenmore device. Otherwise, you might have to ask kenmore (via phone) to email you any video tutorials that they have available or be open to scheduling an in-home repair appointment with them. Thank you.