Grohe Freehander Adjustable Shower Head System Chrome - Answered Questions & Fixed issues

What is a grohe shower ??

the problem is the hot/cold mix is set wrong ---
remove the water control handle to expose the mix valve -- you should see a small set screw that will either increase or decrease the travel of the hot water valve. --- sometimes instead of a set screw there is a little pop off plastic set ring,, pop off and set to a more advanced travel.
this will increase the amount of hot water that flows to the shower head and the bath tap.

c...

try this link copy and paste https://www.youtube.com/watch?v=pxQaL1wpf0U ..

SEE YOUR LOCAL DEALER AND ASK THEM

Step 1
Turn off the water to your faucet.
Step 2
Remove the handle to the faucet. Remove the small screw under the lever handle with an Allen wrench or Phillips head screwdriver, depending on what type of screw is present. Slide the handle back and off the faucet.
Step 3
Remove the temperature control knob, which is the round, dial-shaped fitting over the faucet cartridge. Put the manufacturer-supplied adapter on the cartridge. Line up the lever stop pin with the arrow symbol on the cartridge.
Step 4
Turn on the water and rotate the adapter to the left, or counter-clockwise, until the water temperature is at the level you want. Take note of the number to which the adapter points.
Step 5
Shut the faucet off by turning the adapter to closed and line up the limit stop dial with the number you noted previously.
Step 6
Assemble the faucet by replacing the temperature control knob and handle, then tighten the handle screw. Turn on the water and operate the faucet. If temperature is not set properly, repeat as necessary until you achieve the right setting.

Order repair kit and rebuild flash assembly.

Hi Timothy, What's the model and if you have a photo will help.

so that good or not?

Seal with leak fix or similar sealant

K zaveri The pole the U clamp is attached to should be able to be removed. My own shower has a similar set up. The pole's top and bottom mount's front has a pop out of which has a screw underneath. Once you remove the screw the top bracket can be pulled aside and the pole removed so the U clamp can be slid off. I hope this design works for you as well Have a good day,

Hi Franco, This appears to be on a bath tub. You will have to remove your handle to access this control and simply turn the valve left or right as needed to give you more hot or cold water, whichever it is you are needing. You do NOT need to dismantle the faucet to do this adjustment. Just remove the handle and a cover plate is usually all that is needed for the adjustment. Have a great day!

I would remove the handle and escutcheon plate and grab the front of the faucet cartridge with pliers and see if it is hard to turn now. If it is then there must be an issue with the handle being on too tight or it is binding with with the escutcheon plate somehow. If the cartridge is hard to turn after removing the handle etc. I would pull the cartridge out and grease it using heat proof grease (Plumber's grease) and reinstall it. Make not of it's position when you remove it so as to reinstall in the same position. There isn't any reason I can think of other than the above for the faucet to not turn easy.

The cap on what?

flush fill valve failing

Replacing GROHE 46 298 KHO is as like as replacing other shower heads. 1. Remove old one. 2. Remove excess materials 3. Wrap with teflon tape 4. Install your new GROHE 46 298 KHO Thanks.

Contact a vendor on Amazon and ask if a manual can be provided. Offer to pay for a scanned digital copy or if necessary a photocopy. https://www.amazon.com/GROHE-cooler-carbonator-40554-40554001/dp/B00I4SJ1W8 Amazon com GROHE Blue cooler and carbonator 40554 for use with table water...

InLet valve diaphtagm need replacing

If there is no set screw then it is a friction fit.

has parts and exploded view You are viewing shower spares for Grohe Tempesta Cosmopolitan system 160...