20 Most Recent KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher - Page 9 Questions & Answers

Shut door and press start

Try unplugging ribbon from control board to touchpad. If that doesn’t help, touch pad is probably bad.

Control board issue most likely

Please provide s model # so I can give right answers because there is few deferent model was built

First, remove internal filter below the bottom rotor. Work carefully so you can reinstall. If you have a wet/dry vac, shopvac, remove the filter bag and then suck out the water and clean the bottom of the machine. ( the sump, the low spot inside the appliance. ) Sometimes a popcorn husk or a bit of glass or plastic can get by the filter and clog the pump. The sump is designed to retain a little water between cycles to keep the seals wet so don't worry if there is a bit left after a cycle. (not enough to cover the bottom but a 1/2 cup or so). If this doesn't solve you problem, check the drain hose from end to end. Sometimes it can get too sharp a bend or plug at the sink end.

Replace the control panel.

Turn the power off for a minute or unplug it for a minute.

In the bottom of the dishwasher, there is a filter the size of a glass, twist it and it will release.

Hold the 4 hour delay button down for 3 seconds.

You can try cutting power to unit a breaker box for a couple minutes. That may reset the electronics. If that doesn’t work, then control board is most likely defective.

Hi..Push the energy save button and hold for at least 4 seconds.This will solve your problem.

I see no question here.

First, I'm not a Kitchenaid representative. * Check your warranty. Call for support; 1 (800) 422-1230 * Contact; https://www.kitchenaid.com/major-appliances/refrigeration/refrigerators.html *** The following is for information only.*** * Official "How to maintain" (see cleaning); https://producthelp.kitchenaid.com/Refrigeration/Full-size_Refrigerators * Removing trays; https://www.youtube.com/watch?v=fvoO_x55u3E * Crisper Drawer info; https://www.youtube.com/watch?v=U3bfBAVqaJc Aloha, ukeboy57 Additional information; * Track replacement (Roper); https://www.youtube.com/watch?v=Boh8vhEIt2w * Vitafresh; https://www.youtube.com/watch?v=z5WfVC2OaVA * Support truck; https://www.youtube.com/watch?v=9SazO4SMTqY

I would suspect that the control panel is shorted.

First, I'mn ot a Kitchenaid Representative.* Check your warranty. Call for support.*** following for imfomation only.**** Reset; https://www.google.com/search?q=kitchenaid+dishwasher+reset&ie=utf-8&oe=utf-8&client=firefox-b-1-ab* Reboot; https://www.youtube.com/watch?v=XJnzzXJcOV4* Not running full cycle; https://www.youtube.com/watch?v=QTr0HSwuCCw* Control Locked; https://www.youtube.com/watch?v=BZUUR39bawY* Error codes; https://www.youtube.com/watch?v=Ti48mP2ShKk* Starts then stops; https://www.youtube.com/watch?v=Okfns8OoR1g8 Reset button?; https://www.youtube.com/watch?v=113SZ39zmtI* Cleaning filter Part1 (of 3); https://www.youtube.com/watch?v=Wttz4fB1yVs* Note; opening internal (of box) may void warranty. Call for service.Aloha, ukeboy57

The dishwasher may use the heating coil to increase the water temp, Also utensils fall into the bottom of the unit and can melt. The heater coil may be about to fail and when this happens the temp increases. The filament inside the coil may have worked its way to the outer shell. Last but not least, the pump motor could be overheating.

check here for a pic....... http://www.appliancepartspros.com/control-panel-latch-parts-for-kitchenaid-kudc10ixss4.html there is a screw part # 4 that maybe loose or missing. though it doesn't show one on each side ck it out. hope this helps a little.

Sears Parts Direct, https://www.searspartsdirect.com/model-number/kfcp22exmp1/0593/0161000.html , lists the refrigerator door panel for the KFCP22EXMP1 for $387.47 . The freezer door panel is $517.17 . This is the only site that I found that lists the doors as in stock. This status may change without notice. I hope this helps. Cindy Wells

Short answer NOPE! Get a different repairman to come and retest the fault.