Top 20
American Standard 5 ft Sliding Shower Door - Page 3 Questions & Answers
Repair crack in floor of acrylic shower
Hello their is a product called Plasweld,it comes in a handy tube,
Carefully scratch along the crack to allow the weld to come flush with the surface of the shower tray,MUST BE PERFECTLY DRY!
squeeze into the crack and it will find its own level ,this produce actually welds the plastic together
Good builders merchants should stock this item.GOOD LUCK
9/3/2014 2:04:06 PM •
American...
•
130 views • 0 helpful votes
1.6 toilet will not fill
Make sure the water valve to the toilet is actually letting water into the fill valve. Turn off valve, remove from fill valve, run water into a pan to see pressure and confirm water flow. If water flow and pressure good, replace the fill valve.
8/12/2014 2:45:19 AM •
American...
•
166 views • 0 helpful votes
Bottom of bowl is stained very much. Appears to be a defect in the the finish?
Try using one of these A product called Kaboom Bowel Blaster and let it sit in the bowl for a while, then brush clean. This worked for me when others failed. You can try muriatic acid as a toilet bowl cleaner.Again let it sit for a while then brush and flush available from places like Home depot.Sometimes the toilets are not glazed as well as they should be you might call it a defect I call it poor quality control.
8/1/2014 6:20:49 PM •
American...
•
134 views • 0 helpful votes
I have an American Standard (right height) beig in color. Bowl has a large brown stain near the bottom.
Probably a mineral buildup. Pour a bucket of water into the bowl so that the bowl flushes but does not refill with water. In other words you want as little water in the bowl as possible so it wont dilute the cleaner. Use an acid cleaner like lime away in the bowl. Let it set for several hours or over night,. then scrub with toilet brush. Lime away is fairly safe but try not to splash it on your clothes or yourself. Wash it away if you do.
You may have to repeat to finish the job.
8/1/2014 6:26:40 PM •
American...
•
109 views • 0 helpful votes
Flow of water into american standard toilet tank is very slow and does not fill up to water mark
Adjust the level of the float, water level should be about 1/2" below top of overflow pipe. Slow filling can be due to a build up of calcium in fill vale, a partially blocked water valve, the washer many times gets deteriorated by the chlorine in the water, breaks up and clogs the fill line. Also many manufacturers (fluid-master in particular) place water restrictors inside the bottom of the fill tubes, which cause the water to fill much slower.
5/11/2014 7:22:56 PM •
American...
•
459 views • 0 helpful votes
Hydromassage 1063
Not normal for that to happen but the jet faces on the two back jets may be turned off or down.
Try turning the face of the jet clockwise and see if you get more water flow out of each jet.
Rod
US Parts Center
4/13/2014 5:21:12 PM •
American...
•
934 views • 0 helpful votes
How to do you reset the float
The older styles have a screw at the end of the shaft where the fill valve is, turn the screw in and out to adjust float arm level. Newer ones have a plastic nut and bolt about midway along the shaft. Turn the nut to loosen slightly, push the float up or down and tighten the nut. Caution: The plastic bolt breaks easily so don't tighten the nut too much.
5/7/2014 6:33:15 PM •
American...
•
130 views • 0 helpful votes
Fluidmaster 400 instructions
Depends on type. Rubber ones usually are suspended from the seat by an arm on either side, you pull it off the arms and replace the same way. Older ones slide down over the overflow tube.
5/8/2014 1:01:13 AM •
American...
•
111 views • 0 helpful votes
Whirpool bath starts when I press button but stops as soon as I release button
Hi Joey, The problem is likely that the switch is installed incorrectly. I'm sorry I don't recommend or advise any repair of a appliance that is water/electrical by anyone other than an authorized repair person. Furthermore, I would not use the appliance again until you have have professional repairs done.
5/20/2014 8:32:46 PM •
American...
•
56 views • 0 helpful votes
Pump runs normally with no water but surges when filled with water
When there is a load on the motor and it is surging this is an indication of not enough water getting to the front of the pump.
Check the water flowing inside the tub going from the jet opposite the suction cover.
Sounds to me like you may be getting cavitation because the pump is pulling in too many air bubbles from the jet.
Close the air control and/or move the direction of the eyeball from pointing at the suction cover and see if that helps.
Rod
US Parts Center
4/9/2014 1:53:23 PM •
American...
•
104 views • 0 helpful votes
I have a jetted tub and it won't turn off. I have a single button in the back right corner and i don't know what to do!
Right now you are having to turn it on/off by using the circuit breaker or just unplugging the pump right?
Is this a button you depress or an electric button like you would find on a microwave?
If it is a button you depress to turn it on/off then the problem is most likely the air switch located in the motor under the skirt of the tub.
If it is an electric button then it may be the control box under the tub that needs to be replaced.
Rod
US Parts Center
888-521-6183
2/2/2014 6:06:02 PM •
American...
•
338 views • 0 helpful votes
Down stair toilet bubbles when upstair toilet is flushed. never had this problem with old toilet
The roof vent for the toilets is shared. It is the pipe (on the roof) that lets water in the drain system. When clogged, it causes what you have. A garden hose placed in the roof vent (and turned on) may clear the blockage (could be leafs or pine straw or a dead bird). Needs to be cleared... I have used a plumbers snake with 100% success....but you may not have one...so the garden hose suggestion. Be careful on the roof.
3/1/2014 1:10:32 PM •
American...
•
137 views • 0 helpful votes
Not finding what you are looking for?