Saniflo & Saniplus& Macerator Pump - Answered Questions & Fixed issues

A washing machine discharges water water at a very high velocity and high capacity. This is far more waste water than the pump was designed to handle. The washer discharge must be connected to what's called an "indirect waste", that is, it must discharge into a laundry tub or sump, so that the excess can be stored until it can be taken by the pump. The specific code that governs this is in chapter 27 of the International Residential Code. Also in the manufacturers instructions, they allow the discharge from a washing machine ,through an indirect waste. [sic] "The Sanivite is a drain pump that is ideally suitable for use in a basement apartment or anywhere in the house where additional fixtures are most wanted. It will pump waste water away from a variety of sources such as: a kitchen sink, laundry sink, washing machine ***(indirect connection)***, dishwasher, bar sink, etc." This pump will never be able to handle the discharge directly and you need to provide a receptor to accommodate a washing machine. Is there any possibility of adding a laundry tub adjacent the washer and Sanivite pump?

To the best of my knowledge many traditional designs of taps are still available and while the internal threads might or might not be Imperial, the connection thread invariably is. I have in the past changed the interior parts of taps that are badly worn and even cannibalising old taps of similar size and design I found some would fit and others wouldn't. Each manufacturer would choose the thread pitch and form that suited them best from the great many Imperial threads available so while the internals of the taps of a single manufacturer would interchange, the interchangeability with other brands would be accidental. There is usually a salvage yard in most districts as well as scrapyards and recyclers - lots of exploring to do.

go to this link might help you out... Saniflo toilet wont flush Google Search

Here are a few sites just copy and paste any of these in your browser.

http://www.needplumbingsupplies.com/NeedPlumbingBrands.asp?MfgRqst=10 (this all one link...)

Here is the Saniflo homepage


http://www.saniflo.com/?gclid=COaXi8vxyJkCFQENDQodOnOjsg


Next tag

http://www.nextag.com/saniflo-toilet-systems/products-html

and one more...pricegrabber

http://indoors.pricegrabber.com/bathroom-toilets/saniflo/p/1538/


I hope this helps and good luck...and thanks for rating my effort....the Fang

plug lines

There are two wires, doesn`t matter which way round you connect tham

Motor bearings are damaged, they now have a "tight spot" which you might be able to feel if you rotate the shaft by hand OR motor windings are damaged and overheating causing the motor to stop.

Not enough water (Sani`s don`t suck it in) Recycled dense paper Old Sani needs a service One or all of the above should cure it.

It will be split or damage can easy be seen

Are you in the UK? Approx` age of pump? Model of Saniflo or if unknown what appliances does it serve?

There is no reset button on that model. Suggest putting a plug on the cable and trying another source of power first. Or could be a problem with the cutting disc being jammed or the condenser has blown. If more that 5yrs old then replace the whole pump.

If the water in the pan is slow to drain then possibly a restriction in the pan outlet or the membrane is slow to react to the water pressure, lastly if it is old and noisy the motor windings are damaged so in this case could be time for a new pump.

indicates a blocked or very dirty unit. Try cleaning with a saniflo cleaner - can be intorduced via wc bowl without unit removal. if this fails then its time to remove the unit and clean / look for blockages

This post about the same problem has proved helpful. Hope it works for you Google Groups

Contact the manufacturer for local suppliers.

Can you remove the lid (top) and adjust the ball cock? It may be stuck.

sound like the motor seized or windings degraded. REPLACE MAY CAUSE HEAT DAMAGE.

Sounds like your float inside the unit is hung up on debris or is defective. DW

water pressure check for lime scale

Check the GFCI breaker at the outlet, if equipped, or if there is a dedicated circuit breaker at main panel box. DW