20 Most Recent
KitchenAid Architect Series KEBC107KSS Electric Single Oven - Page 2 Questions & Answers
Fault code F2E0
Your key pad is shorted.Replace the electronic range control clock.
After using the self cleaning
If you slide your oven out and take off the center panel on the back of the oven you will see the thermal fuse. If it's like mine, it will be located (looking from the back of the oven) upper right hand side. It's an oblong loooking part with two terminals with wires attached to it and two screws holding it on. Once you take it off, you will notice that it is flat on the back side and you should be able to see part # 9759242. Only reason I know this is that I have just removed mine and am going to see if I can find one locally. Same thing happened to mine after putting it in the cleaning cycle to clean up after the holidays.
Hope this helps!
Robert
I have a kitchen add KGSS907 it is showing an
F6 E0 means the switch pulse return line to the electronic control is not connected
The usual way to correct this is to replace the electronic control (clock).
You might want to check for loose or burnt out wires on the clock unit before replacing tho'.
How do I remove the
Open the door about 3" this is the "vent heat" location. Lift up and out on the door, pay attention to the hinges and their position, so you can reinstall the door without any problems.
11/18/2010 12:25:30 AM •
KitchenAid...
•
Answered
on Nov 18, 2010
Oven shut down during
Hi!!
Follow this instructions to stop Self-Clean any time:
Press CANCEL OFF - CANCEL OFF If the oven temperature is too high, the door will remain locked. It will not unlock until the oven cools.
If the control panel do not respond, the self-cleaning timer is over, and the oven is cool, unplug the unit from the wall outlet, wait a couple of minutes and plug it back in. This will reset the control board.
Keep me posted!!
Hi, Don't know if you
This a 50 % problem of the probe and 50% problem of the PC board. It excactly as you figure it out.
the correct procedure in any case is to proceed first with the probe test for a couple of days and then if no diference you should replace the PC Board.
In this you dont loose anything since in the second case for a new PC Board then it is recomented to have a new probe also.
The handle has fallen off
Yes the door has to be disassembled to repair the handle. In some cases you can just loosen the sides and top and work with it on your lap without removing from the unit but it takes patience and an extra set of hands is nice to have around. Any visible screws have to come out first. Eric
Trying to clean oven get code F3E2
Thanks for your question!
I'm sorry that you haven't received an answer yet.
The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...
Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.
Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.
Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!
If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question
Springs make a horrendous noise when you open the door.
Hi,
The best repair is to replace the hinges and springs. If you do want to lubricate them do NOT use grease or wd40, these are flammable and do not mix well with heat.
Look up an appliance parts store in your city and pick up some high temperature copper or graphite based lubricant those are safe for use on oven hinges.
Cant turn it off, it seems to be locked?
hELLO THERE
On some of these ovens they have a internal reset device that needs to be reset and this is done by unplugging the oven and waiting for one hour then plugging it back in and waiting for 5 min befor you attempt to unlock it.
Now on some of the newer model ovens all you have to do is unplug wait 15 sec and plug it back in for 5 sec then repeat this step 3 times ok so please try these and let me know how this goes
Best regards Michael
Our KitchenAid KEMS803 recently stopped
F6 - E0
Return line not connected
If switch pulse return line is not connected, electronic control will display F6 within 60 seconds after power up. Replace control board.
No heat after self-cleaning
This was my exact problem. Our oven is almost identical, but mine so this could likely be the same fix. Check the details
here:
This post was helpful as well:
here.
Not finding what you are looking for?