Top 20
Jacuzzi BK37959 White Era?? Two-Piece Elongated Toilet BK37 - Page 6 Questions & Answers
Hottub drained itself
If your hot tub water has all drained then you need to look for a leak obviously.
Start in the cabinet area where there are unions attaching the pump and the electronics. Sometimes those will vibrate loose and will begin to leak.
If all the unions are tight and you see no water then you need to start to look elsewhere around the tub for water leaks. It could be a broken manifold in the plumbing or a jet body.
Rod
US Parts Center
3/9/2014 10:29:25 AM •
Jacuzzi Home
•
151 views • 0 helpful votes
Model identification
While the brand of the tub may be of importance to you it may not be important when finding parts for it.
Bath tub manufacturers do not make anything that goes into their tubs i,e. the jets, pumps and controls are all purchased from various Mfg.
Are you have any particular problems with either unit that would make you need the brand of either?
Rod
U S Parts Center
1/5/2014 3:56:31 PM •
Jacuzzi Home
•
530 views • 1 helpful votes
Need to see how to get the switch on/off switch removed from the tub
The air button is located on the top lip of the bathtub or just below the top lip on the sidewall.
It is held in place by a nut that is threaded up the length of the air button body.
In order to change the air button you will need access to the underside of that air button so the nut can be unthreaded off the button body.
Rod
US Parts Center
2/26/2014 7:32:08 PM •
Jacuzzi Home
•
92 views • 0 helpful votes
Replacing jet
When you installed the new jet, did you install a new gasket on the wall fitting or use 100% RTF type silicone?
In order to seal a wall fitting that is cracked an leaking, the replacement must have either the gasket or silicone to seal the wall fitting against the wall of the tub or it will leak when filled with water.
Rod
U S Parts Center
1/3/2014 1:08:45 AM •
Jacuzzi Home
•
325 views • 0 helpful votes
Burning smell
get it checked by electrician. there has to be an access panel.
10/10/2013 1:28:21 AM •
Jacuzzi Home
•
871 views • 0 helpful votes
Jacuzzi hot tub will not reach temp pumps do run?
If your hot tub is running but NOT heating then you need to look at a couple of things.First, on the topside, is the heat indicator light on?If it is on and the tub is not heating then the temp sensor or the high limit sensor is not working and need to be replaced.US Parts Center
10/22/2013 7:02:08 PM •
Jacuzzi Home
•
475 views • 0 helpful votes
I have a jetted tub that the air switch does not
This actually sounds like you have some calcium built up on the inside of the air button.Take the trim ring off the air button and pull out the center button.Get some soft emery cloth and run it around the outside of the center button and well as the inside of the button body then reinstall. That should solve your problem with a sticking air button.US Parts Center
10/17/2013 3:00:08 AM •
Jacuzzi Home
•
319 views • 0 helpful votes
My jacuzzi is flashing FL1 and the heater isnt
FL is a "flow" issue. Check the filter to make sure it is clean. Start by removing it from the tub and see if that solves the error. The next item to check is the gate valves to make sure they are open all the way. There are usually one on either side of the pump and control box.
Rod
US Parts Center
8/19/2013 9:22:32 PM •
Jacuzzi Home
•
803 views • 0 helpful votes
I have a leak where The air switch is. The leak is
The Air Tubing presses onto the little nipple on the underside of the air button. There is no seal on this set up. Once the air hose is attached to the nipple there should no air leakage when the air button is pressed.Before you install the air hose you might cut off half inch on the end to make sure the end has not splits and you get a good piece of hose so it will seal properly.US Parts Center
8/30/2013 12:18:35 PM •
Jacuzzi Home
•
266 views • 0 helpful votes
Not finding what you are looking for?